Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Palm Treo 650 LCD Screen Replacement

Cosa ti serve

  1. Palm Treo 650 LCD Screen Replacement, Battery and Stylus: passo 1, immagine 1 di 1
    • Position the phone so the screen faces down.

    • Remove the stylus found on the back of the phone.

  2. Palm Treo 650 LCD Screen Replacement: passo 2, immagine 1 di 1
    • Hold the button in the middle of the phone's back to remove the battery cover.

    • Slide the cover down to remove it, and set the cover aside.

  3. Palm Treo 650 LCD Screen Replacement: passo 3, immagine 1 di 2 Palm Treo 650 LCD Screen Replacement: passo 3, immagine 2 di 2
    • Lift the edge of the battery, separating contact points, and pull out as pictured.

  4. Palm Treo 650 LCD Screen Replacement, Case: passo 4, immagine 1 di 1
    • Remove the round, rubber cover to expose a screw that will be removed in the next step.

  5. Palm Treo 650 LCD Screen Replacement: passo 5, immagine 1 di 2 Palm Treo 650 LCD Screen Replacement: passo 5, immagine 2 di 2
    • Remove the six 6.9 mm screws as pictured with a T5 Torx screwdriver.

    • Remove the single 9.8 mm screw next to the antenna on the back plate, using a Phillips #00 screwdriver.

  6. Palm Treo 650 LCD Screen Replacement: passo 6, immagine 1 di 1
    • Pull the antenna outward to remove the antenna from the body of the phone.

  7. Palm Treo 650 LCD Screen Replacement: passo 7, immagine 1 di 2 Palm Treo 650 LCD Screen Replacement: passo 7, immagine 2 di 2
    • Pry the back cover off using an iFixit opening tool.

    • Several small clips on the inside attach to the back cover.

  8. Palm Treo 650 LCD Screen Replacement, Motherboard: passo 8, immagine 1 di 3 Palm Treo 650 LCD Screen Replacement, Motherboard: passo 8, immagine 2 di 3 Palm Treo 650 LCD Screen Replacement, Motherboard: passo 8, immagine 3 di 3
    • Disconnect the ribbon cable before removing the motherboard.

    • Unclip the gray tab.

    • Pull out the orange ribbon cable.

  9. Palm Treo 650 LCD Screen Replacement: passo 9, immagine 1 di 2 Palm Treo 650 LCD Screen Replacement: passo 9, immagine 2 di 2
    • Pull off the motherboard.

  10. Palm Treo 650 LCD Screen Replacement, LCD Screen: passo 10, immagine 1 di 3 Palm Treo 650 LCD Screen Replacement, LCD Screen: passo 10, immagine 2 di 3 Palm Treo 650 LCD Screen Replacement, LCD Screen: passo 10, immagine 3 di 3
    • Lift up the LCD screen so that the ribbon strip connecting it to the motherboard can be accessed.

    • Be careful not to pull off LCD screen yet.

  11. Palm Treo 650 LCD Screen Replacement: passo 11, immagine 1 di 2 Palm Treo 650 LCD Screen Replacement: passo 11, immagine 2 di 2
    • Unclip the gray tab.

    • Pull out the orange ribbon strip.

    • Remove the LCD screen.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

cgood

Membro da: 10/28/09

122 Reputazione

7 Guide realizzate

Team

Cal Poly, Team 19-3, Maness Fall 2009 Membro di Cal Poly, Team 19-3, Maness Fall 2009

CPSU-MANESS-F09S19G3

4 Membri

18 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 5,116