Aggiusta la tua roba

Diritto alla Riparazione

Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Palm Treo 650 Earphone Replacement

Scritto Da: cgood (e 6 altri collaboratori)
  • Commenti: 0
  • Preferiti: 2

Difficoltà

Moderato

Passi

10

Tempo Necessario

10 minuti

Sezioni

4

Contrassegni

4

Student In Progress

Studente In Lavorazione

Questa guida è in lavorazione da parte di studenti laboriosi.

Grammar Police

Vigilanza sulla Grammatica

Adotta il tuo insegnante di inglese interno e contribuisci a migliorare la grammatica di questa guida!

Inconsistent Images

Immagini Non Adeguate

Aggiornare le immagini per renderle più in sintonia con le prerequisite aumenterebbe l'attrattiva di questa guida.

Incorrect Tools

Attrezzi Non Corretti

Contribuisci a rendere migliore questa guida usando i giusti strumenti nelle immagini e/o nel testo.

Introduzione

A quick guide to replacing the earphone in the palm treo.

  1. Position the phone so the screen faces down.

    • Position the phone so the screen faces down.

    • Remove the stylus found on the back of the phone.

    Traduci

  2. To remove the battery cover, hold down the button in the middle of the phone's back.

    • To remove the battery cover, hold down the button in the middle of the phone's back.

    • Slide the cover down to remove. Set the cover aside.

    Traduci

  3. Lift the edge of the battery, separating contact points, and pull out as pictured. Lift the edge of the battery, separating contact points, and pull out as pictured.

    • Lift the edge of the battery, separating contact points, and pull out as pictured.

    Traduci

  4. Remove the small round rubber cover on the back of the phone located immediately below the antenna.

    • Remove the small round rubber cover on the back of the phone located immediately below the antenna.

    • This will uncover a screw that will be removed in the next step.

    Traduci

  6. Unscrew the screws around the back plate with a T5 Torx Screwdriver. Six black 6.9 mm Torx screws

    • Unscrew the screws around the back plate with a T5 Torx Screwdriver.

    • Six black 6.9 mm Torx screws

    • Unscrew the screw next to the antennae on the back plate.

    • One 9.75 mm Phillips antenna screw with a Phillips #00 Screwdriver.

    Traduci

  7. Remove the antennae.

    • Remove the antennae.

    Traduci

  8. Pry the back cover off using a spudger or similar tool. The back cover is attached by several small clips on the inside.

    • Pry the back cover off using a spudger or similar tool.

    • The back cover is attached by several small clips on the inside.

    Traduci

  9. Disconnect the ribbon cable before removing the motherboard. Unclip the gray tab. Pull out the orange ribbon cable.

    • Disconnect the ribbon cable before removing the motherboard.

    • Unclip the gray tab.

    • Pull out the orange ribbon cable.

    Traduci

  10. Pull off the mother board. Install replacement or repaired motherboard, reversing steps above.

    • Pull off the mother board.

    • Install replacement or repaired motherboard, reversing steps above.

    Traduci

  11. Pull out the earphone by grabbing the black rubber piece. Pull out the earphone by grabbing the black rubber piece. Pull out the earphone by grabbing the black rubber piece.

    • Pull out the earphone by grabbing the black rubber piece.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 6 altri collaboratori

cgood

Membro da: 28/10/2009

122 Reputazione

7 Guide realizzate

Distintivi: 10

+7 altri distintivi

Team

Cal Poly, Team 19-3, Maness Fall 2009 Membro di Cal Poly, Team 19-3, Maness Fall 2009

CPSU-MANESS-F09S19G3

4 Membri

18 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 1

Tutti i Tempi: 2,822