Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

PSP 300xc Power Switch Board Replacement

Introduzione

Has the power switch broken on your precious PSP 300xc? Replace the power switch board, and set everything right once more.

Cosa ti serve

  1. PSP 300xc Power Switch Board Replacement, Battery: passo 1, immagine 1 di 2 PSP 300xc Power Switch Board Replacement, Battery: passo 1, immagine 2 di 2

    • Press the button securing the battery door to the PSP 300xc, and lift the battery door off.

    • Lift the battery out of the PSP.

    Traduci

  2. PSP 300xc Power Switch Board Replacement, Front Case: passo 2, immagine 1 di 1

    • Use a spudger or your fingernail to remove the warranty sticker stuck to the inside of the battery tray

    Traduci

  3. PSP 300xc Power Switch Board Replacement: passo 3, immagine 1 di 2 PSP 300xc Power Switch Board Replacement: passo 3, immagine 2 di 2

    • Remove four Phillips screws from the back of the PSP.

    Traduci

  4. PSP 300xc Power Switch Board Replacement: passo 4, immagine 1 di 1

    • Remove two Phillips screws from the top of the PSP.

    Traduci

  5. PSP 300xc Power Switch Board Replacement: passo 5, immagine 1 di 1

    • Remove a single screw from the bottom edge of the PSP.

    Traduci

  6. PSP 300xc Power Switch Board Replacement: passo 6, immagine 1 di 2 PSP 300xc Power Switch Board Replacement: passo 6, immagine 2 di 2

    • Insert a spudger between the front case and PSP, and slide the spudger along the perimeter of the front case to remove it.

    Traduci

  8. PSP 300xc Power Switch Board Replacement, LCD: passo 7, immagine 1 di 1

    • Remove a single Phillips screw securing the home bar to the PSP 300xc.

    Traduci

  9. PSP 300xc Power Switch Board Replacement: passo 8, immagine 1 di 2 PSP 300xc Power Switch Board Replacement: passo 8, immagine 2 di 2

    • Push the home bar to the right about 1cm to release a tab, and begin to lift the right end of the home bar slightly.

    • Do not attempt to remove the home bar yet, it is still attached to the PSP 300xc.

    Traduci

  10. PSP 300xc Power Switch Board Replacement: passo 9, immagine 1 di 1

    • Insert a spudger under the LCD, beside the black plastic tab.

    • Push the LCD to the left and pry up to release the left edge of the LCD from under the plastic tab.

    Traduci

  11. PSP 300xc Power Switch Board Replacement: passo 10, immagine 1 di 1

    • Insert a spudger under the LCD, beside the black plastic tab.

    • Push the LCD to the right and pry up to release the right edge of the LCD from under the plastic tab.

    Traduci

  12. PSP 300xc Power Switch Board Replacement: passo 11, immagine 1 di 3 PSP 300xc Power Switch Board Replacement: passo 11, immagine 2 di 3 PSP 300xc Power Switch Board Replacement: passo 11, immagine 3 di 3

    • Rotate the LCD away from the PSP to reveal the LCD and home bar ribbon cables.

    • Use your fingernail or the edge of a plastic opening tool to flip up the retaining flap on the following four ZIF connectors:

    • Home bar cable

    • Microphone cable

    • LCD display data cable

    • Touchscreen cable

    • Be sure you are prying up on the retaining flap, not the socket itself

    • After flipping up the locking tabs on all four connectors, use your fingers or a spudger to gently pull the cables straight out of the connectors.

    Traduci

  13. PSP 300xc Power Switch Board Replacement: passo 12, immagine 1 di 1

    • Remove the LCD from the PSP 300xc.

    Traduci

  14. PSP 300xc Power Switch Board Replacement, Home Bar: passo 13, immagine 1 di 3 PSP 300xc Power Switch Board Replacement, Home Bar: passo 13, immagine 2 di 3 PSP 300xc Power Switch Board Replacement, Home Bar: passo 13, immagine 3 di 3

    • Lift the home bar up as high as it will go, but not so high that the wires disconnect.

    • Try to bend the small tab under the silver rim as little as possible it the following steps. The more you bend, the more likely it will snap.

    • Twist the home bar counter clockwise while carefully lifting it further. The left edge has to lift over the black plastic frame to allow it to rotate.

    • The home bar should now lift out of the PSP 300xc.

    Traduci

  15. PSP 300xc Power Switch Board Replacement, Trigger Buttons: passo 14, immagine 1 di 2 PSP 300xc Power Switch Board Replacement, Trigger Buttons: passo 14, immagine 2 di 2

    • Remove both trigger buttons by lifting them off the PSP 300xc.

    Traduci

  16. PSP 300xc Power Switch Board Replacement, Power Switch Board: passo 15, immagine 1 di 1

    • Using a finger or spudger, flip up the retaining flap on the power switch board ribbon cable socket.

    • Pull the ribbon cable out of its socket.

    Traduci

  17. PSP 300xc Power Switch Board Replacement: passo 16, immagine 1 di 1

    • Using the flat end of a spudger, pry the power switch board up and off the PSP 300xc.

    • Remove the power switch board from the PSP.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 2 altri collaboratori

Matthew Newsom

Membro da: 01/05/10

39.496 Reputazione

67 Guide realizzate

Distintivi: 47

+44 altri distintivi

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 8

Ultimi 30 Giorni: 24

Tutti i Tempi: 8,419