Introduzione

Guide for removing the Analog stick in a Sony PSP-3000

Place the PSP face down and locate the battery cover on the left side of the device.
  • Place the PSP face down and locate the battery cover on the left side of the device.

  • Lift and remove the battery cover to reveal the battery.

  • Remove the battery.

Aggiungi Commento

Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.
  • Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

Aggiungi Commento

  • Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.

    • Two are located behind the battery's warranty sticker.

    • Two are located on the right side of the PSP.

Aggiungi Commento

  • Next, unscrew the two screws located at the top of the PSP.

Aggiungi Commento

  • Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

Aggiungi Commento

  • Slide the spudger in between the outer casing of the PSP, beginning at the "R" shoulder button, and gently pry off the casing.


  • Remove the front casing completely.

Aggiungi Commento

  • Push the homebar to the right to release the tab located on the right side of the LCD screen.

  • DO NOT completely remove the homebar, as it is still connected by ribbon cables.

Aggiungi Commento

  • Slowly lift the LCD screen off the PSP starting at the top edge corner.

  • Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

    • Orientation of PSP is flipped in photo.

Aggiungi Commento

  • Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.

  • Pull all four ribbon cables out.

  • Now remove the LCD screen and homebar from the PSP.

Aggiungi Commento

  • Remove the metal tab that lies above the LCD screen.

  • Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

Aggiungi Commento

  • Remove the screw securing 'L' trigger to the PSP.

Aggiungi Commento

  • Remove the white plastic piece that holds the 'L' trigger in place.

Aggiungi Commento

  • Remove the 'L' trigger from the PSP.

Aggiungi Commento

  • Remove the screw securing the 'R' trigger.

Aggiungi Commento

  • Remove the white plastic piece that holds the 'R' trigger in place.

Aggiungi Commento

  • Remove the 'R' trigger from the PSP.

Aggiungi Commento

  • Remove the screw from the bottom left edge of the PSP.

Aggiungi Commento

  • Being careful not to break the ribbon cable, use the spudger to peel the adhesive button of the the 'L' trigger off the PSP.

Being careful not to break the ribbon cable, use the spudger to peel the adhesive button of the 'L' trigger off the PSP.

buzinon - Replica

  • Using a fingernail or spudger, flip up the retaining bracket on the d-pad and 'L' trigger ribbon cable.

  • Lift the black plastic bracket along with the d-pad contact pad, disconnecting the ribbon cable as you lift.

Aggiungi Commento

  • Remove the cable from the connector and remove the entire black piece from the PSP.

Aggiungi Commento

  • Remove the screw holding the analog stick in place.

Aggiungi Commento

  • Flip up the lock on the analog sticks ribbon cable.

  • Remove the analog stick from the PSP.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 12 persone hanno completato questa guida.

mbnewsom

Membro da: 28/10/2009

2.360 Reputazione

12 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 4

Ultimi 7 Giorni: 43

Ultimi 30 Giorni: 160

Tutti i Tempi: 17,015