Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Oster 6329 Power Cord Replacement

Introduzione

Removing the power cord is straightforward, but it does require soldering.

Cosa ti serve

  1. Oster 6329 Power Cord Replacement, Outer Shell Removal: passo 1, immagine 1 di 2 Oster 6329 Power Cord Replacement, Outer Shell Removal: passo 1, immagine 2 di 2

    • Using the Phillips-head #2 screwdriver, unscrew the three 1cm Phillips-head screws on the plastic base of the toaster to separate the outer metal shell from the plastic base.

    Traduci

  2. Oster 6329 Power Cord Replacement: passo 2, immagine 1 di 1

    • Push the plastic push-down handle down and pull the plastic handle straight from metal arm.

    Traduci

  3. Oster 6329 Power Cord Replacement: passo 3, immagine 1 di 1

    • Loosen the outer metal shell from the plastic base by holding the plastic base while pulling up on the metal shell.

    • Only lift the outer shell a little so as not to disconnect the cables that connect the circuit board.

    Traduci

  4. Oster 6329 Power Cord Replacement: passo 4, immagine 1 di 2 Oster 6329 Power Cord Replacement: passo 4, immagine 2 di 2

    • Disconnect the cable clips from the circuit board using the tweezers to free the outer metal shell from the plastic base.

    Traduci

  6. Oster 6329 Power Cord Replacement: passo 5, immagine 1 di 2 Oster 6329 Power Cord Replacement: passo 5, immagine 2 di 2

    • Lift the top outer metal shell.

    • Carefully lift the outer metal shell at an angle so as not to damage the components in the front of the toaster.

    Traduci

  7. Oster 6329 Power Cord Replacement, Power Cord: passo 6, immagine 1 di 1

    • Using a flat-head screwdriver, pry the power cord from the base of the toaster.

    Traduci

  8. Oster 6329 Power Cord Replacement: passo 7, immagine 1 di 1

    • Using a flat-head screwdriver, pry the white wire from the base.

    Traduci

  9. Oster 6329 Power Cord Replacement: passo 8, immagine 1 di 1

    • Locate the circuit board at the front of the toaster where the power cord and white wire meet.

    • Pull the circuit board up and out to free the circuit board from the body of the toaster.

    • It is tightly fit and may take moderate force to remove.

    Traduci

  10. Oster 6329 Power Cord Replacement: passo 9, immagine 1 di 2 Oster 6329 Power Cord Replacement: passo 9, immagine 2 di 2

    • Desolder the power cord from the circuit board at the locations show in the diagram.

    • For soldering instructions see the iFixit Soldering Guide.

    • The wires should be free from board when un-soldering is complete.

    Traduci

  11. Oster 6329 Power Cord Replacement: passo 10, immagine 1 di 2 Oster 6329 Power Cord Replacement: passo 10, immagine 2 di 2

    • Unscrew the two 1.5cm Phillips-head screws at the back of the toaster that are holding the power cord in place to remove the retaining clip.

    • Remove the plastic retaining clip that is holding the cord in place.

    Traduci

  12. Oster 6329 Power Cord Replacement: passo 11, immagine 1 di 2 Oster 6329 Power Cord Replacement: passo 11, immagine 2 di 2

    • Untie the knot in the power cord.

    Traduci

  13. Oster 6329 Power Cord Replacement: passo 12, immagine 1 di 1

    • Pull the cord from the base to remove the cable.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 6 altri collaboratori

Timothy Grijalva

Membro da: 01/31/14

234 Reputazione

2 Guide realizzate

Distintivi: 8

+5 altri distintivi

Team

Cal Poly, Team 13-15, Regan Winter 2014 Membro di Cal Poly, Team 13-15, Regan Winter 2014

CPSU-REGAN-W14S13G15

5 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 11

Tutti i Tempi: 856