Aggiusta la tua roba Comunità Store

Oster 3905 Retractable Cord Replacement

Introduzione

If your Oster 3905 cord isn’t retracting like the yo-yo you secretly still use, it may be time to replace it. While this replacement guide is pretty straight forward - watch out! There is a nasty little spring that will try to pop out and blind you.

Cosa ti serve

  1. Oster 3905 Retractable Cord Replacement, Slot Levers: passo 1, immagine 1 di 1

    • Firmly grip your hand around the slot lever.

    Modifica

  2. Oster 3905 Retractable Cord Replacement: passo 2, immagine 1 di 1

    • Stabilize the toaster by placing your hand on top.

    Modifica

  3. Oster 3905 Retractable Cord Replacement: passo 3, immagine 1 di 2 Oster 3905 Retractable Cord Replacement: passo 3, immagine 2 di 2

    • Forcefully pull the slot lever away from the toaster by keeping parallel to the table.

    Modifica

  4. Oster 3905 Retractable Cord Replacement: passo 4, immagine 1 di 1

    • Both slot levers can be removed.

    Modifica

  5. Oster 3905 Retractable Cord Replacement, Outer Shell: passo 5, immagine 1 di 1

    • Place the toaster upside down so the bottom is facing the ceiling.

    Modifica

  6. Oster 3905 Retractable Cord Replacement: passo 6, immagine 1 di 2 Oster 3905 Retractable Cord Replacement: passo 6, immagine 2 di 2

    • Take off both rubber feet using a small metal spudger.

    • Wedge a spudger under the feet and pull up to pop off.

    Modifica

  7. Oster 3905 Retractable Cord Replacement: passo 7, immagine 1 di 1

    • Use a PH#2 screw bit to remove eight 12mm screws that are located around the perimeter.

    • There are two screws under the rubber feet.

    Modifica

  9. Oster 3905 Retractable Cord Replacement: passo 8, immagine 1 di 1

    • Place the toaster right side up.

    Modifica

  10. Oster 3905 Retractable Cord Replacement: passo 9, immagine 1 di 2 Oster 3905 Retractable Cord Replacement: passo 9, immagine 2 di 2

    • Grab the outer shell firmly and pull up towards the face of the toaster.

    Modifica

  11. Oster 3905 Retractable Cord Replacement: passo 10, immagine 1 di 1

    • For this part, you might need to wiggle the toaster to get the outer shell off.

    • The shell will not completely come off until the motherboard is removed in the next step.

    Modifica

  12. Oster 3905 Retractable Cord Replacement: passo 11, immagine 1 di 3 Oster 3905 Retractable Cord Replacement: passo 11, immagine 2 di 3 Oster 3905 Retractable Cord Replacement: passo 11, immagine 3 di 3

    • Use a J1 screw bit to unscrew eight 8mm screws from the motherboard.

    Modifica

  13. Oster 3905 Retractable Cord Replacement: passo 12, immagine 1 di 2 Oster 3905 Retractable Cord Replacement: passo 12, immagine 2 di 2

    • Take out the grey “cancel” and “bagel” buttons from the shell.

    Modifica

  14. Oster 3905 Retractable Cord Replacement, Retractable Cord: passo 13, immagine 1 di 1

    • Rotate the toaster so that the back is facing towards you.

    Modifica

  15. Oster 3905 Retractable Cord Replacement: passo 14, immagine 1 di 2 Oster 3905 Retractable Cord Replacement: passo 14, immagine 2 di 2

    • Use the PH#1 bit to remove one 8mm screw located above the wire on the casing.

    • Then use the same screw bit to remove two 10mm screws found at the bottom.

    Modifica

  16. Oster 3905 Retractable Cord Replacement: passo 15, immagine 1 di 2 Oster 3905 Retractable Cord Replacement: passo 15, immagine 2 di 2

    • Using the metal spudger, pry next to the black clip found at the base of the toaster and the casing.

    • Push down to separate the casing from the toaster.

    Modifica

  17. Oster 3905 Retractable Cord Replacement: passo 16, immagine 1 di 2 Oster 3905 Retractable Cord Replacement: passo 16, immagine 2 di 2

    • Gently tilt the casing towards the toaster as you pull up from the base.

    Modifica

  18. Oster 3905 Retractable Cord Replacement: passo 17, immagine 1 di 1

    • Use the PH#1 bit to remove the three 8mm screws located on the back side of the casing.

    Modifica

  19. Oster 3905 Retractable Cord Replacement: passo 18, immagine 1 di 2 Oster 3905 Retractable Cord Replacement: passo 18, immagine 2 di 2

    • When opening the casing a metal spring may suddenly pop out.

    • Use the metal spudger to pry open the two halves of the casing.

    • If you are having some trouble only using the metal spudger do not be afraid of using your fingers to pry the casing apart.

    Modifica

  20. Oster 3905 Retractable Cord Replacement: passo 19, immagine 1 di 3 Oster 3905 Retractable Cord Replacement: passo 19, immagine 2 di 3 Oster 3905 Retractable Cord Replacement: passo 19, immagine 3 di 3

    • Carefully remove the spool keeping your fingers on either side of the casing.

    • Tape down the metal spring to keep it from unraveling out of place.

    Modifica

  21. Oster 3905 Retractable Cord Replacement: passo 20, immagine 1 di 3 Oster 3905 Retractable Cord Replacement: passo 20, immagine 2 di 3 Oster 3905 Retractable Cord Replacement: passo 20, immagine 3 di 3

    • Carefully unwind the power cord from the spool.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 3 altri collaboratori

Adam Dierkes

Membro da: 09/12/16

140 Reputazione

1 Guida realizzata

Distintivi: 6

+3 altri distintivi

Team

CSU Fullerton, Team 2-1, Bruce Fall 2016 Membro di CSU Fullerton, Team 2-1, Bruce Fall 2016

CSUF-BRUCE-F16S2G1

5 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 6

Tutti i Tempi: 528