Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. , Copertura posteriore: passo 1, immagine 1 di 2 , Copertura posteriore: passo 1, immagine 2 di 2
    • Prima di iniziare, spegni il tuo telefono.

    • Rimuovi il carrello della scheda SIM.

  2. : passo 2, immagine 1 di 1
    • Svita le due viti Torx T2 da 2,5 mm.

    • Il OnePlus 5T non usa molto adesivo per tenere ferma la copertura posteriore. Comunque i ganci sono parecchio resistenti e richiedono della forza durante la procedura di apertura.

  3. : passo 3, immagine 1 di 3 : passo 3, immagine 2 di 3 : passo 3, immagine 3 di 3
    • Infila uno strumento di apertura tra lo schermo e la copertura posteriore sotto la parte inferiore del telefono.

    • Usa lo strumento per creare una fessura tra la copertura posteriore e lo schermo.

    • Infila un plettro nella fessura che hai creato con lo strumento di apertura.

  4. : passo 4, immagine 1 di 3 : passo 4, immagine 2 di 3 : passo 4, immagine 3 di 3
    • Fai scorrere il plettro verso l'angolo in basso a destra del telefono.

    • Infila un secondo plettro e fallo scorrere verso l'angolo in basso a sinistra del telefono.

  5. : passo 5, immagine 1 di 3 : passo 5, immagine 2 di 3 : passo 5, immagine 3 di 3
    • Fai scorrere il plettro attorno all'angolo in basso a sinistra e quindi verso l'alto sotto il bordo sinistro del telefono per rilasciare i ganci in plastica che tengono ferma la copertura posteriore.

  6. : passo 6, immagine 1 di 3 : passo 6, immagine 2 di 3 : passo 6, immagine 3 di 3
    • Fai scorrere il plettro attorno all'angolo in basso a destra e quindi verso l'alto sotto il bordo destro del telefono per rilasciare i ganci in plastica che tengono ferma la copertura posteriore.

  7. : passo 7, immagine 1 di 3 : passo 7, immagine 2 di 3 : passo 7, immagine 3 di 3
    • Cerca di non rimuovere ancora del tutto la copertura posteriore. I cavi a nastro del sensore delle impronte, della porta di carica e della presa jack sono ancora collegati alla scheda madre.

    • Gira il tuo telefono e solleva attentamente la parte inferiore della copertura posteriore dal corpo del telefono. Giralo a sinistra e tienilo ad un angolo di 80°.

  8. : passo 8, immagine 1 di 2 : passo 8, immagine 2 di 2
    • Usa uno spudger per sollevare e scollegare il cavo a nastro del sensore delle impronte.

  9. : passo 9, immagine 1 di 3 : passo 9, immagine 2 di 3 : passo 9, immagine 3 di 3
    • Ruota la copertura posteriore di 180° ed appoggiala allineandone il bordo inferiore con il bordo superiore della batteria.

  10. : passo 10, immagine 1 di 3 : passo 10, immagine 2 di 3 : passo 10, immagine 3 di 3
    • Usa un paio di pinzette per rimuovere la piccola copertura in metallo che copre i connettori dei cavi a nastro della batteria, della porta di carica e della presa jack.

  11. : passo 11, immagine 1 di 2 : passo 11, immagine 2 di 2
    • Usa uno spudger per sollevare e scollegare il cavo a nastro della porta di carica e della presa jack.

  12. : passo 12, immagine 1 di 2 : passo 12, immagine 2 di 2
    • Rimuovi la copertura posteriore.

  13. , Scollega la batteria: passo 13, immagine 1 di 2 , Scollega la batteria: passo 13, immagine 2 di 2
    • Usa uno spudger per sollevare e scollegare il cavo a nastro della batteria.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 14, immagine 1 di 1
    • Remove the six Phillips #00 screws (2.9 mm length).

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 15, immagine 1 di 3 : passo 15, immagine 2 di 3 : passo 15, immagine 3 di 3
    • Slide an opening pick underneath the left side of the speaker.

    • Use the opening pick to pry the speaker up and out of its recess.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 16, immagine 1 di 2 : passo 16, immagine 2 di 2
    • Remove the speaker.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 17, immagine 1 di 2 : passo 17, immagine 2 di 2
    • Use a spudger to pry up and disconnect the display flex cable.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 18, immagine 1 di 2 : passo 18, immagine 2 di 2
    • Slide an opening pick under the left side of the interconnect cable and pry it up.

    • The interconnect cable is held in place by mild adhesive. In case you're having trouble removing it, you can apply a heated iOpener to loosen the adhesive underneath.

  19. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 19, immagine 1 di 1
    • Apply a heated iOpener to the screen and all edges of the phone for at least two minutes, to loosen the adhesive.

  20. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 20, immagine 1 di 3 : passo 20, immagine 2 di 3 : passo 20, immagine 3 di 3
    • If the phone's screen is cracked, the suction handle may not stick. Try lifting it with strong tape, or superglue the suction handle in place and allow it to cure so you can proceed.

    • Once the screen is warm to the touch, apply a suction cup to the bottom edge of the phone.

    • Pull the suction cup upwards and insert an opening pick in the gap between the display glass and the midframe. Start to cut the adhesive by sliding the opening pick to the bottom right corner.

  21. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 21, immagine 1 di 2 : passo 21, immagine 2 di 2
    • Insert a second opening pick and slide it to the bottom left corner of the phone to cut the adhesive.

    • Leave the picks in place to prevent the adhesive from resealing.

  22. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 22, immagine 1 di 3 : passo 22, immagine 2 di 3 : passo 22, immagine 3 di 3
    • Insert a third opening pick under the bottom left corner of the phone.

    • Slide the opening pick up to the top left corner to cut the adhesive. Leave it there to prevent the adhesive from resealing.

    • If cutting becomes too difficult, reheat and reapply the iOpener.

  23. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 23, immagine 1 di 2 : passo 23, immagine 2 di 2
    • Insert a fourth opening pick at the top left corner.

    • When nearing the front facing camera, only work with the tip of the opening pick to avoid damaging or smearing the camera.

    • Slide the opening pick along the top edge of the phone to cut the adhesive. Leave the pick in the top right corner of the screen to prevent the adhesive from resealing.

  24. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 24, immagine 1 di 2 : passo 24, immagine 2 di 2
    • Insert a fifth opening pick and slide it along the right edge of the phone to cut the remaining adhesive.

    • Try not to remove the display all the way yet, the display cable is still threaded through the frame and possible adhered on the inner side of the midframe.

  25. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 25, immagine 1 di 3 : passo 25, immagine 2 di 3 : passo 25, immagine 3 di 3
    • Thread the display flex cable through the gap in the midframe and remove the display.

    • Before installing a new display, remove all traces of the old adhesive from the frame, and clean the glued areas with isopropyl alcohol (>90%) and a lint-free cloth.

    • If your replacement part doesn't come with preattached adhesive, the best way to secure the new screen is with a sheet of custom-cut double-sided tape. Apply the tape to the back of the screen, then carefully feed the display cable through the frame. Align the screen and press it into place.

Linea Traguardo

Altre 10 persone hanno completato questa guida.

Team

iFixit Membro di iFixit

Staff

136 Membri

16.578 Guide realizzate

Un commento

What adhesive do you use? B-7000 glue , 1mm or 2mm adhesive tape?

purepeanutz - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 7

Ultimi 7 Giorni: 52

Ultimi 30 Giorni: 245

Tutti i Tempi: 22,693