Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 1
    • Turn the laptop upside-down, with the handle facing away from you.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 2 : passo 2, immagine 2 di 2
    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 2 : passo 3, immagine 2 di 2
    • Lift up on the middle of the battery to remove it from the device.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 2 : passo 4, immagine 2 di 2
    • Remove the two 2mm Phillips #1 screws from beneath the battery lock tabs.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 3 : passo 5, immagine 2 di 3 : passo 5, immagine 3 di 3
    • Flip the laptop over to its normal position.

    • Lift the two antennas on both sides to unlock the screen.

    • Open the laptop.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 2 : passo 6, immagine 2 di 2
    • Be careful not to pull the keyboard too far because there is still a ribbon cable attached to the bottom.

    • Gently lift up on the back of the keyboard.

    • Pull the keyboard up far enough to expose the ribbon cable.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 2 : passo 7, immagine 2 di 2
    • Gently lift up on the black connector to release the ribbon cable.

    • Gently pull the blue plastic tab up and away from the black connector.

    • Remove the keyboard from the laptop.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 2 : passo 8, immagine 2 di 2
    • Close and flip the laptop over so you are looking at the battery compartment

    • Remove the five 4mm Phillips #1 screws from inside the battery compartment

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 3 : passo 9, immagine 2 di 3 : passo 9, immagine 3 di 3
    • Flip the laptop over, showing the top of the device.

    • Open the laptop and rotate the screen ninety degrees.

    • Tilt the screen so the lower right corner of the screen is closer to the lower case.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 3 : passo 10, immagine 2 di 3 : passo 10, immagine 3 di 3
    • Push in and lift up on the keyboard edge of the white handle piece.

    • Pull the piece towards yourself to remove it from the laptop.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 1
    • Remove the four 4mm Phillips #1 screws attaching the green trim to the body of the computer.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 12, immagine 1 di 2 : passo 12, immagine 2 di 2
    • Pry off the rear green trim piece.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 13, immagine 1 di 3 : passo 13, immagine 2 di 3 : passo 13, immagine 3 di 3
    • Be careful not to pull the bottom portion of the laptop completely off, as there is a cable connecting it to the laptop.

    • Slide the green trim pieces away from the screen.

    • This should release the entire bottom portion of the laptop.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 14, immagine 1 di 3 : passo 14, immagine 2 di 3 : passo 14, immagine 3 di 3
    • Unplug the cable from the mouse buttons controller to completely remove the lower frame from the device.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 15, immagine 1 di 2 : passo 15, immagine 2 di 2
    • Rotate the entire lower assembly up slightly, and pull it away from the screen to free it from the screen hinge.

    • There may be some adhesive holding the cable to the metal plate. Gently pull the cable off of the plate if it is stuck.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 16, immagine 1 di 3 : passo 16, immagine 2 di 3 : passo 16, immagine 3 di 3
    • You should now be looking at the bottom of the lower case.

    • Remove the eight 4mm Phillips #1 screws attaching the green trim pieces to the lower frame.

    • Pry off the front and side trim pieces.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 17, immagine 1 di 1
    • Remove the two 4mm Phillips #1 screws that attach the mouse buttons controller to the lower frame.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 18, immagine 1 di 3 : passo 18, immagine 2 di 3 : passo 18, immagine 3 di 3
    • Disconnect the ribbon cable attached to the keyboard compartment.

    • Unplug the ribbon cable between the touchpad and the mouse buttons controller.

    • Remove the mouse buttons controller from the device.

Linea Traguardo

Team

Cal Poly, Team 3-30, Amido Winter 2013 Membro di Cal Poly, Team 3-30, Amido Winter 2013

CPSU-AMIDO-W13S3G30

3 Membri

12 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 315