Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Nvidia Shield Tablet Motherboard Replacement

Cosa ti serve

  1. Nvidia Shield Tablet Motherboard Replacement, Rear Case: passo 1, immagine 1 di 2 Nvidia Shield Tablet Motherboard Replacement, Rear Case: passo 1, immagine 2 di 2
    • First, remove the stylus from your tablet.

  2. Nvidia Shield Tablet Motherboard Replacement: passo 2, immagine 1 di 3 Nvidia Shield Tablet Motherboard Replacement: passo 2, immagine 2 di 3 Nvidia Shield Tablet Motherboard Replacement: passo 2, immagine 3 di 3
    Attrezzo utilizzato in questo passaggio:
    Anti-Static Wrist Strap
    $7.95
    Compra
    • Set the tablet so the buttons, microSD, and stylus port are facing you.

    • Open the microSD slot.

    • Using the flat end of the spudger tool, carefully pry open the case starting from the microSD slot, slowly sliding the spudger along the inside edge of the case.

    • You may want to put on your anti-static wrist strap at this point as the motherboard will be vulnerable to physical touch and electrostatic shock after the casing is removed.

  3. Nvidia Shield Tablet Motherboard Replacement: passo 3, immagine 1 di 2 Nvidia Shield Tablet Motherboard Replacement: passo 3, immagine 2 di 2
    • As you remove your case, be aware of small clips along the edges.

    • Finally, set the old casing aside.

  4. Nvidia Shield Tablet Motherboard Replacement, Motherboard: passo 4, immagine 1 di 1
    • Carefully use the precision tweezers to unplug the ribbon cable.

    • Be sure to have your anti-static wrist strap on for this procedure.

  5. Nvidia Shield Tablet Motherboard Replacement: passo 5, immagine 1 di 3 Nvidia Shield Tablet Motherboard Replacement: passo 5, immagine 2 di 3 Nvidia Shield Tablet Motherboard Replacement: passo 5, immagine 3 di 3
    • Remove the two 6.5 mm Phillips #00 screws and seven 3.0 mm Phillips #00 screws.

  6. Nvidia Shield Tablet Motherboard Replacement: passo 6, immagine 1 di 3 Nvidia Shield Tablet Motherboard Replacement: passo 6, immagine 2 di 3 Nvidia Shield Tablet Motherboard Replacement: passo 6, immagine 3 di 3
    • Use a pair of tweezers to disconnect the three black antenna cables from the motherboard.

    • Use the flat end of the spudger tool to carefully pry up the motherboard.

    • In the first Shield, the stylus ribbon cable is located under the right side of board. While there are 2 additional cables for the cameras underneath the left end of the board. Be sure to loosen the cameras before lifting the board.

  7. Nvidia Shield Tablet Motherboard Replacement: passo 7, immagine 1 di 2 Nvidia Shield Tablet Motherboard Replacement: passo 7, immagine 2 di 2
    • Desolder the positive and negative battery cables from the motherboard.

    • Make sure to note which wire goes where, you don't want to re-solder the wires backwards!

    • The motherboard should now come free.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 6 persone hanno completato questa guida.

Molly Bauer

Membro da: 08/27/15

1.424 Reputazione

6 Guide realizzate

Team

USF Tampa, Team 2-2, Blackwell Fall 2015 Membro di USF Tampa, Team 2-2, Blackwell Fall 2015

USFT-BLACKWELL-F15S2G2

3 Membri

11 Guide realizzate

9 Commenti

Where do you obtain a new motherboard?

imprintcave - Replica

The real question is more about how to find a new shield tablet motherboard ??

willixlive - Replica

where can i buy the motherboard

Gurjot Dhaliwal - Replica

waar kan ik een nieuw shield moederbord kopen?

tom1vangestel - Replica

Hello, I'm looking for a description of the various ribbon connectors on the motherboard.

I'm also looking for a hint to solve a problem I have after replacing the screen+digitizer: the right side (half) of the touch screen does'n work.

Laurent Zanoni - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 24

Tutti i Tempi: 9,220