Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Nook Tablet Midframe Replacement

Introduzione

Use this guide to replace the midframe of your Nook Tablet. This guide is also a prerequisite for accessing or replacing most of the Nook's internal components.

Cosa ti serve

  1. Nook Tablet Midframe Replacement, Back Cover: passo 1, immagine 1 di 1

    • Flip the Nook over.

    Traduci

  2. Nook Tablet Midframe Replacement: passo 2, immagine 1 di 2 Nook Tablet Midframe Replacement: passo 2, immagine 2 di 2

    • Lift the flap that reads "Nook" to reveal the tape that is underneath. Remove the memory card if one is present.

    • Remove the tape covering the round holes to reveal two T5 Torx screws.

    • Remove the two T5 Torx screws securing the back cover.

    Traduci

  3. Nook Tablet Midframe Replacement: passo 3, immagine 1 di 2 Nook Tablet Midframe Replacement: passo 3, immagine 2 di 2

    • Insert the flat end of a spudger between the front panel and the rear assembly.

    • Though these photos show a screwdriver, use a spudger or plastic opening tool in order to prevent damage to the device.

    • Use a spudger to lift the the back panel from the rest of the Nook.

    Traduci

  4. Nook Tablet Midframe Replacement: passo 4, immagine 1 di 2 Nook Tablet Midframe Replacement: passo 4, immagine 2 di 2

    • Slide the spudger around the edges of the Nook to loosen the back panel.

    Traduci

  6. Nook Tablet Midframe Replacement: passo 5, immagine 1 di 1

    • Pull the back panel off the Nook.

    Traduci

  7. Nook Tablet Midframe Replacement, Screen Bezel: passo 6, immagine 1 di 2 Nook Tablet Midframe Replacement, Screen Bezel: passo 6, immagine 2 di 2

    • Using the T5 Torx screwdriver, remove the ten T5 screws from around the edges of the silver midframe.

    Traduci

  8. Nook Tablet Midframe Replacement: passo 7, immagine 1 di 2 Nook Tablet Midframe Replacement: passo 7, immagine 2 di 2

    • Using a spudger or plastic opening tool, carefully pry the screen bezel away from the silver midframe.

    Traduci

  9. Nook Tablet Midframe Replacement, Disconnect the Battery: passo 8, immagine 1 di 2 Nook Tablet Midframe Replacement, Disconnect the Battery: passo 8, immagine 2 di 2

    • Lift up the foam pad at the corner of the battery to reveal the battery connector.

    • Use a spudger or plastic opening tool to disconnect the battery cable from the motherboard.

    • These photos show a screwdriver, but we recommend using a nonconductive tool like a spudger to prevent a potential short.

    Traduci

  10. Nook Tablet Midframe Replacement, Midframe: passo 9, immagine 1 di 1

    • Lift up the foam that covers the power connector and volume connector.

    • Disconnect the power and volume cables from their sockets on the motherboard.

    Traduci

  11. Nook Tablet Midframe Replacement: passo 10, immagine 1 di 2 Nook Tablet Midframe Replacement: passo 10, immagine 2 di 2

    • Carefully lift the silver midframe away from the motherboard and display assembly.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 1 altro collaboratore

Holly Lowe

Membro da: 09/26/12

238 Reputazione

3 Guide realizzate

Distintivi: 13

+10 altri distintivi

Team

Cal Poly, Team 1-4, Propen Fall 2012 Membro di Cal Poly, Team 1-4, Propen Fall 2012

CPSU-PROPEN-F12S1G4

4 Membri

14 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 4

Tutti i Tempi: 406