Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Usa uno spudger in metallo per rimuovere le coperture in plastica bianca delle viti incastrate nella copertura inferiore vicino alla parte anteriore della Wii.
-
-
-
Apri la porta protettiva delle prese dei controller finché è perpendicolare con la cornice nera delle prese.
-
Tira verso l'alto la porta protettiva per separarla dalla copertura esterna.
-
-
-
-
Svita la piccola vite a croce Phillips che fissa la porta della batteria alla copertura inferiore.
-
Sfila la porta della batteria dalla Wii.
-
-
-
Utilizza delle pinzette per sollevare il connettore della ventola e rimuoverlo dalla sua presa sulla scheda logica.
-
-
-
Rimuovi le tre viti a croce Phillips da 10 mm che fissano la staffa nera al pannello inferiore accanto alla parte frontale della Wii.
-
Solleva leggermente la staffa e utilizza l'altra mano per tirare via la clip di bloccaggio da dove le antenne Wi-Fi entrano nella copertura della scheda madre.
-
Rimuovi la staffa dalla Wii.
-
-
-
Rimuovi le quattro viti Phillips da 11,3 mm che fissano il dissipatore di calore al pannello inferiore.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the side of the Wi-Fi board furthest away from the heat sink and lift it out of its socket on the motherboard, being careful not to put too much sideways force on the connector.
-
Remove the Wi-Fi board & antennas from the Wii.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger or your fingertips to lift up the end of the Bluetooth board nearest the center of the motherboard.
-
Carefully peel the front edge of the Bluetooth board off the EMI foam attached to the motherboard.
-
Remove the Bluetooth board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingernail to flip up the DVD drive ribbon cable retaining flap.
-
Pull the DVD drive ribbon cable out of its socket and remove it from the Wii.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully pull the DVD drive power cable away from its socket on the motherboard and remove it from the Wii.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully grab the motherboard by its edges and lift it off the bottom panel.
-
Annulla: non ho completato questa guida.
Altre 40 persone hanno completato questa guida.
5 Commenti
Any idea if there is a common issue effecting these motherboards that causes them to fail? Perhaps I'm wondering if there is a best-practice method for determining where and/or why my Wii's MB failed (circuit tracing, component testing, soldered fuses, etc.). Upon lengthy inspection, I am unable to find any components with the usually noticeable burn marks, leaky/exploded capacitors, discolored parts or similar visual cues telling me why this MB failed.
And as a side note, I've already testing this Wii's power supply and it's 100%.
Thoughts?
I just found this post about on-board fuses, but the other parts of my original question still apply.
Nintendo Wii Drive Board Fuse Replacement
If I determine it's a fuse-related issue, I'll post an update here.
Our WII unit was hit by a power surge…was not able to get it to work after that. Will motherboard replacement likely resolve most issues related to this?
Thank you for these detailed instructions! I was able to replace my original 01 board with rev. 60 and it's working beautifully! Can't thank you enough!