Introduzione
Hai fatto cadere il tuo DSi XL nella piscina? Utilizza questa guida per riparare o sostituire la scheda madre.
Cosa ti serve
-
-
Rimuovi le due viti a croce Phillips che fissano la copertura della batteria al retro della console portatile.
-
Rimuovi la copertura della batteria dal retro del DSi XL.
-
-
-
Rimuovi le quattro coperture di gomma delle viti del case inferiore facendo leva su di loro con una puntina.
-
-
-
-
Utilizza uno spudger per sollevare il cavo del microfono dalla scheda madre.
Note that the WiFi board has already been removed here! Including this extra step would be convenient here '-)
-
-
-
Utilizzando l'estremità piatta di uno spudger, capovolgi il nastro di bloccaggio sul connettore ZIF del cavo dati del display inferiore.
-
Con l'estremità appuntita di uno spudger, tira il display inferiore del cavo dati dal suo connettore sulla scheda madre.
-This is where you can replace the charger port. i may change this comment later from May 21-June 5
-
-
-
Utilizzando l'estremità piatta di uno spudger, solleva il cavo della batteria dalla sua presa sulla scheda madre.
The battery connectors (socket) on the mother board are extremely fragile, so care should be taken to avoid breaking them.
Other than this, the instructions given are precise and straighforward. I do agree with the other comments about step 20.
-
-
-
Rimuovi le viti che fissano la scheda madre al case superiore:
-
Una sola vite argentata a croce Phillips da 2,5 mm
-
Quattro viti a croce Phillips nere da 3,7 mm
the battery connector was (for me) extremely hard to remove. I broke the socket completely off the board hand had to hard solder it directly back.
-
-
-
Utilizzando l'estremità piatta di uno spudger, capovolgi il nastro di bloccaggio sul connettore ZIF del cavo dati del display superiore.
-
Con l'estremità appuntita di uno spudger, tira il cavo dati del display superiore dal suo connettore al di sotto della scheda madre.
This step is unnecessary. The ribbon is a total pain in the butt to get back in, and if you dont get it PERFECT, the DS will not even fire back up. Unless it is absolutely necessary to remove it... DON'T !!! ( Personal experience, Everything else was SPOT ON) THANK YOU FOR THE HELP, saved me a lot of $$$
Fantastic! Fixed my daughter's irreplaceable DSi XL - you should see her smiles!! Not sure about step 20 I did this before reading the comments (guess there's a message there). Thanks so much whoever wrote this - you're a legend and you've made a child very happy (and a dad too thereby).
I put mine back together for my daughter with the new bottom screen, but it won't power on. It tries but won't I'm assuming that this ribbon is the cause.
The instructions are perfect though! Great thing to have these instructions it's a tremendous help! :-)
YHWH is the god of all knowledge. Put a piece of transparent tape on the ribbon cable to give more leverage to pull the cable up to slide it into the slot. Also turn the motherboard slightly so that you can get it closer to the cable.
I didn't get mine completely reinserted at first. The symptom I experienced when powering it back on is the power light comes on briefly and the bottom screen light flashes, then they both shut off. No flash from the upper display. Had to try reinserting 3 times before I had it in completely. I agree, DON'T REMOVE if you don't have to.
-
Per rimontare il tuo dispositivo, segui queste istruzioni in ordine inverso.
Per rimontare il tuo dispositivo, segui queste istruzioni in ordine inverso.
Annulla: non ho completato questa guida.
Altre 20 persone hanno completato questa guida.
Un ringraziamento speciale a questi traduttori:
100%
Questi traduttori ci stanno aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›
rust/white powder built up on a screw and can’t unscrew it
Eco - Replica