Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. , Rimozione copertura batteria: passo 1, immagine 1 di 2 , Rimozione copertura batteria: passo 1, immagine 2 di 2
    • Svita le due viti a croce Philips che fissano il copribatteria al case inferiore.

    • Le viti rimangono attaccate al copribatteria.

    • Prendi il copribatteria e sollevalo dal case inferiore.

    • Se è difficile da prendere, picchietta delicatamente la parte opposta del dispositivo.

  2. , Rimozione batteria: passo 2, immagine 1 di 2 , Rimozione batteria: passo 2, immagine 2 di 2
    • Usando uno spudger (o un'unghia), solleva la batteria dalla parte superiore.

    • L'indicatore danneggiamento da liquidi si trova al di sotto della batteria. Fai leva delicatamente, o potresti danneggiare l'indicatore.

    • Troverai una piccola aletta al di sopra della batteria che renderà la rimozione più semplice.

    • Prendi la batteria e rimuovila dal DSi.

    This is also where the water damage indicator is located, if that's important

    [REDACTED] - Replica

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 2 : passo 3, immagine 2 di 2
    • Two screws are hidden underneath two rubber feet highlighted in red.

    • Use the tip of a spudger to pry the rubber feet out of the lower case.

    • Depending on the age of your device, the rubber feet may crumble apart as you pry them out. If so, use a fine-tipped tool to scrape out any stuck pieces of rubber.

    One of the feet did break on me, tweezers came in handy for picking it out

    Willie Narvaez - Replica

    I unfolded and sharpened a paperclip. You can use that to stab and hook the rubber without tearing it, as the rubber is thick enough to reseal when reinserted.

    Keegan Andersen -

    Nasty, broke my spudger and the feet in this step.

    TimedIn - Replica

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 1
    • Remove the following screws securing the lower case to the body of the DSi:

    • Six 5.2 mm Phillips #00 screws.

    • One 2.7 mm Phillips #00 screw.

    Impossible d'enlever les vises… trop serré! comment faire?

    evrobert03 - Replica

    i can't get the screw by the gamecard slot out, PH#00 is too small and PH#0 is too big

    Iblowup - Replica

    same problem here. maybe try a JIS?

    darth mango -

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 3 : passo 5, immagine 2 di 3 : passo 5, immagine 3 di 3
    • Insert the spudger in between the lower casing and lower panel near the top right corner of the DSi.

    • Carefully run the spudger along the edge of the outer casing, creating an opening between the body and the casing.

    • Continue running the spudger around the body of the DSi until the majority of the lower case has been separated.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 2 : passo 6, immagine 2 di 2
    • Carefully lift the lower casing from its bottom edge.

    • The lower case is still attached to the motherboard by the volume and SD board cable highlighted in red. Do not try to completely remove the lower case of the DSi yet.

    • Pry the volume and SD board cable up from its socket on the motherboard using a spudger.

    • Once the cable is completely removed, then you may take off the entire outer casing.

Linea Traguardo

Altre 8 persone hanno completato questa guida.

Un commento

I found that lower case ribbon cable very hard to plug back in

iSzymon - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 30

Ultimi 30 Giorni: 142

Tutti i Tempi: 13,022