Salta al contenuto principale

Introduzione

This is how you remove the bottom cover

  1. Remove the expansion pack cover by pushing in the tab and pulling out.
    • Remove the expansion pack cover by pushing in the tab and pulling out.

  2. If your system uses a jumper pack, the same procedure applies to remove it.
    • If your system uses a jumper pack, the same procedure applies to remove it.

    • A small spoon can be used in place of a spudger.

    • Lever the expansion pack out using a metal spudger.

  3. Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.
    • Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

  4. Remove the two front feet of the N64.
    • Remove the two front feet of the N64.

  5. Rotate to top side up and lift off top cover.
    • Rotate to top side up and lift off top cover.

  6. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.
    • Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

  7. Batterie per PC portatili

    Una soluzione semplice per un grande aumento di potenza.

    Acquista ora

    Batterie per PC portatili

    Una soluzione semplice per un grande aumento di potenza.

    Acquista ora
  8. Remove the metal plate indicated in the example by sliding it back and then lifting it up. Remove the metal plate indicated in the example by sliding it back and then lifting it up.
    • Remove the metal plate indicated in the example by sliding it back and then lifting it up.

  9. Remove the two screws indicated in the example using the smaller Phillips screwdriver.
    • Remove the two screws indicated in the example using the smaller Phillips screwdriver.

  10. Remove the screw to the right of the LED light using the larger Phillips screwdriver.
    • Remove the screw to the right of the LED light using the larger Phillips screwdriver.

  11. Remove the small metal bracket from the back of the expansion pack slot.
    • Remove the small metal bracket from the back of the expansion pack slot.

  12. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.
    • Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

  13. Remove the small metal bracket behind the expansion slot using the spudger. Remove the small metal bracket behind the expansion slot using the spudger.
    • Remove the small metal bracket behind the expansion slot using the spudger.

  14. Remove the seven screws indicated in the example using the larger Phillips screwdriver. Remove the seven screws indicated in the example using the larger Phillips screwdriver.
    • Remove the seven screws indicated in the example using the larger Phillips screwdriver.

  15. Lift off and remove the metal plate as indicated in the example.
    • Lift off and remove the metal plate as indicated in the example.

  16. Remove the four screws indicated using the #1 Phillips screwdriver.
    • Remove the four screws indicated using the #1 Phillips screwdriver.

  17. Lift up and remove the motherboard.
    • Lift up and remove the motherboard.

  18. Remove everything from the bottom cover.
    • Remove everything from the bottom cover.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 15 persone hanno completato questa guida.

tonymag28

Membro da: 28/10/2009

1.729 Reputazione

3 Guide realizzate

Team

Cal Poly, Team 5-4, Regan Fall 2009 Membro di Cal Poly, Team 5-4, Regan Fall 2009

CPSU-REGAN-F09S5G4

7 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 52

Ultimi 30 Giorni: 402

Tutti i Tempi: 21,403