Aggiusta la tua roba Comunità Store

Nintendo 3DS XL Left Bumper Replacement

Scritto Da: Jack Belcher (e 5 altri collaboratori)
  • Commenti: 1
  • Preferiti: 0

Difficoltà

Moderato

Passi

9

Tempo Necessario

30 minuti - 1 ora

Sezioni

1

Contrassegni

4

Confusing Text

Testo Confuso

Parte del testo di questa guida è confusionario, doppio, o fuori tema. Modificarlo per renderlo più chiaro!

Needs Better Images

Necessarie Immagini Migliori

Delle foto più belle renderanno migliore questa guida. Contribuisci scattando, modificando o caricando immagini nuove!

Better Introduction

Introduzione Migliore

Migliora questa guida completando o revisionando la sua introduzione.

Missing Details

Dettagli Mancanti

Alcuni dettagli di questa guida sono mancanti. Aiuta gli utenti aggiungendo strumenti, livello di difficoltà o tempo di esecuzione.

Introduzione

So, you dropped your 3DS XL, and your left bumper needs to be replaced. This guide will provide the steps to replace the left bumper/left ribbon cable.

  1. Remove the SD card and the game cartridge from the device.

    • Remove the SD card and the game cartridge from the device.

    Modifica

  2. Unscrew the two captive screws on the battery cover panel with a Phillips #00 screwdriver. Remove the battery cover panel. Remove the battery.

    • Unscrew the two captive screws on the battery cover panel with a Phillips #00 screwdriver.

    • Remove the battery cover panel.

    • Remove the battery.

    Modifica

  3. Remove the four visible screws on the battery panel using the Phillips #00 screwdriver. Remove the four visible screws on the battery panel using the Phillips #00 screwdriver.

    • Remove the four visible screws on the battery panel using the Phillips #00 screwdriver.

    Modifica

  5. Remove the screw covers and remove the screws. Remove the screw covers and remove the screws. Remove the screw covers and remove the screws.

    • Remove the screw covers and remove the screws.

    Modifica

  6. Remove the tiny screw by the game card compartment. Remove the tiny screw by the game card compartment.

    • Remove the tiny screw by the game card compartment.

    Modifica

  7. Lift the battery panel off of the device. Grab from the cartridge holder and pull back to remove.

    • Lift the battery panel off of the device.

    • Grab from the cartridge holder and pull back to remove.

    • Be careful to not pull off ribbons from the mother board.

    • Disconnect the ribbon cables from the motherboard.

    Modifica

  8. Remove the left bumper assembly screws. Remove the spring. Spring could eject.

    • Remove the left bumper assembly screws.

    • Remove the spring.

    • Spring could eject.

    • Remove the hinge pin.

    Modifica

  9. Separate the bumper from the bumper assembly.

    • Separate the bumper from the bumper assembly.

    Modifica

  10. Remove and replace the left bumper ribbon cable. Pull carefully on ribbon cable as to not damage the structure.

    • Remove and replace the left bumper ribbon cable.

    • Pull carefully on ribbon cable as to not damage the structure.

    • Can be removed with fingers.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 5 altri collaboratori

Jack Belcher

Membro da: 26/10/2021

169 Reputazione

1 Guida realizzata

Distintivi: 2

Team

University of North Texas, Team 3-1, Thomas Fall 2021 Membro di University of North Texas, Team 3-1, Thomas Fall 2021

UNT-THOMAS-F21S3G1

4 Membri

1 Guida realizzata

Un commento

No steps on how to install the new bumper?

Alex Tomalty - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 30

Ultimi 30 Giorni: 108

Tutti i Tempi: 620