Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Riempi una pentola o una padella con abbastanza acqua per immergerci un iOpener.
-
Scalda l'acqua finché non bolle. Spegni il fuoco.
-
Posiziona l'iOpener nell'acqua calda per 2-3 minuti. Assicurati che l'iOpener sia completamente immerso nell'acqua.
-
Usa delle pinze per estrarre l'iOpener scaldato dall'acqua calda.
-
Asciuga accuratamente l'iOpener con un asciugamano.
-
Il tuo iOpener è pronto all'uso! Se devi scaldare di nuovo l'iOpener, scalda l'acqua fino all'ebollizione, spegni il fuoco e immergi l'iOpener in acqua per 2-3 minuti.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lay a warm iOpener over the LCD glass to soften the adhesive holding it in place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a curved razor blade between the LCD glass cover and the body of D800.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the curved razor blade along the front edge of the LCD.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Bring the blade around the corner of the LCD closest to the shutter button.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the curved razor blade between the long edge of the LCD and the body of the D800.
-
Use the blade to pry the edge of the glass off the LCD.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Work your blade towards the corner nearest the lens.
-
Again, use the blade to separate the glass from the LCD panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
While lifting up with the razor blade, insert a plastic opening pick underneath the LCD glass.
-
Remove the razor blade.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the pick along the top edge of the glass, prying up on the glass against the plastic body as you go.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Leave the first opening pick underneath the front-right corner of the glass.
-
Insert a second opening pick underneath the panel from the back-left side of the display.
-
Slide the pick right, prying up the glass panel as you go.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Once the glass is mostly separated from the camera, peel the panel completely off the LCD screen.
-
At this point there may be some adhesive tape connecting the glass to the camera. If so, simply pull the glass up until it's free.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using rubbing alcohol and a q-tip, clean the old adhesive strips and any residue off the LCD screen.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully align the new LCD protective glass over the display.
-
Lower the left edge of the glass onto the display and press it firmly against the edge of the LCD window.
-
Ease the right edge into place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Press down on the edges of the display to ensure that the glass is strongly-adhered to the LCD.
-
Annulla: non ho completato questa guida.
Altre 9 persone hanno completato questa guida.