Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Introduzione

Excessive use sometimes causes certain ports, such as the AV Port, to cease normal function. This guide explains how to remove the main board from a Nikon D80 camera. For safety purposes, please remove the battery before working with any electronic components.

Please note that this guide requires soldering. For more information on how to solder and desolder connections, please visit this guide.

  1. Using a  Phillips #00  screwdriver, remove the four 6.2 mm screws from the left and right sides of the outer cover. Using a  Phillips #00  screwdriver, remove the four 6.2 mm screws from the left and right sides of the outer cover.
    • Using a Phillips #00 screwdriver, remove the four 6.2 mm screws from the left and right sides of the outer cover.

  2. Use tweezers to gently flip the small locking flap of the zero force insertion connector up. Pull the orange connector cable out of the zero force insertion connector  using the tweezers. Remove the back cover.
    • Use tweezers to gently flip the small locking flap of the zero force insertion connector up.

    • Pull the orange connector cable out of the zero force insertion connector using the tweezers.

    • Remove the back cover.

  3. Kit per Nintendo Switch

    Una soluzione rapida per tornare in gioco

    Acquista Kit per Switch

    Kit per Nintendo Switch

    Una soluzione rapida per tornare in gioco

    Acquista Kit per Switch
  4. Use a Phillips #00 screwdriver to remove the six 3.7 mm screws. Remove the back plate that covers the main board. Remove the back plate that covers the main board.
    • Use a Phillips #00 screwdriver to remove the six 3.7 mm screws.

    • Remove the back plate that covers the main board.

  5. Use a Phillips #00 screwdriver to unscrew the 2.3 mm screw. Use a Phillips #00 screwdriver to unscrew the 2.3 mm screw.
    • Use a Phillips #00 screwdriver to unscrew the 2.3 mm screw.

  6. Use tweezers to gently flip the small locking flaps of the zero force insertion connectors up.
    • Use tweezers to gently flip the small locking flaps of the zero force insertion connectors up.

    • Pull the bottom orange connector cable out of the zero force insertion connector using the tweezers.

    • Pull the top orange connector cable out of the zero force insertion connector using the tweezers.

    • Remove the ribbon cables by gently pulling them away from the no-fuss ribbon cable connectors.

    • Remove the ribbon cables by gently pulling them away from the no-fuss ribbon cable connectors.

    • Disconnect the main board from the two ports on the left by pulling the main board to the right.

  7. Using the soldering iron, disconnect the four wires soldered to the main board. For more information on how to solder and desolder connections, please visit this guide. Be careful when using the hot soldering iron. Move the ribbon cable out of the way as well; it is easy to burn it or yourself when using the iron.
    • Using the soldering iron, disconnect the four wires soldered to the main board.

    • For more information on how to solder and desolder connections, please visit this guide.

    • Be careful when using the hot soldering iron. Move the ribbon cable out of the way as well; it is easy to burn it or yourself when using the iron.

    • Remove the main board.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Sara Martin

Membro da: 09/10/2017

485 Reputazione

4 Guide realizzate

Team

USF Tampa, Team S1-G1, Leahy Fall 2017 Membro di USF Tampa, Team S1-G1, Leahy Fall 2017

USFT-LEAHY-F17S1G1

4 Membri

5 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 23

Tutti i Tempi: 1,203