Aggiusta la tua roba Comunità Store

Nikon D5200 Screen Replacement

Introduzione

Make sure to have your soldering iron ready prior to replacing the screen. This will make the process go faster as the time it takes to heat the soldering iron varies.

Cosa ti serve

  1. Nikon D5200 Screen Replacement, Screen: passo 1, immagine 1 di 3 Nikon D5200 Screen Replacement, Screen: passo 1, immagine 2 di 3 Nikon D5200 Screen Replacement, Screen: passo 1, immagine 3 di 3

    • Fully open the LCD panel so that its screws are easily accessible.

    • Remove the two 2.5 mm screws from the outside edge of the screen casing, and the two 3.5 mm screws from the inside edge.

    Modifica

  2. Nikon D5200 Screen Replacement: passo 2, immagine 1 di 3 Nikon D5200 Screen Replacement: passo 2, immagine 2 di 3 Nikon D5200 Screen Replacement: passo 2, immagine 3 di 3

    • Pry open the plastic casing using the opening tool or by hand.

    Modifica

  4. Nikon D5200 Screen Replacement: passo 3, immagine 1 di 3 Nikon D5200 Screen Replacement: passo 3, immagine 2 di 3 Nikon D5200 Screen Replacement: passo 3, immagine 3 di 3

    • Use the plastic opening tool to pop up the latch holding the ribbon cable on the right side of the circuit board, and remove it.

    • Use the plastic opening tool to pry the ribbon cable on the left side of the circuit board up and off of its socket.

    Modifica

  5. Nikon D5200 Screen Replacement: passo 4, immagine 1 di 2 Nikon D5200 Screen Replacement: passo 4, immagine 2 di 2

    • Using tweezers, unplug the smaller cable.

    Modifica

  6. Nikon D5200 Screen Replacement: passo 5, immagine 1 di 2 Nikon D5200 Screen Replacement: passo 5, immagine 2 di 2

    • Desolder the three small wires on the left side of the circuit board.

    • Soldering irons become very hot when in use. Take all necessary precautions to avoid injury.

    Modifica

  7. Nikon D5200 Screen Replacement: passo 6, immagine 1 di 3 Nikon D5200 Screen Replacement: passo 6, immagine 2 di 3 Nikon D5200 Screen Replacement: passo 6, immagine 3 di 3

    • Using a spudger, remove the display from its casing.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 15 persone hanno completato questa guida.

Autore

con 4 altri collaboratori

Alexander Corn

Membro da: 08/26/15

1.282 Reputazione

5 Guide realizzate

Distintivi: 14

+11 altri distintivi

Team

USF Tampa, Team 3-1, Eyestone Fall 2015 Membro di USF Tampa, Team 3-1, Eyestone Fall 2015

USFT-EYESTONE-F15S3G1

4 Membri

5 Guide realizzate

8 Commenti

Do I need to de-solder if I'm just replacing the window glass?

isaac - Replica

To isaac: no. The exterior glass is separate from the LCD.

Joseph Morris - Replica

Do you recommend the replacent for LCD sold on Ebay?

g_atki - Replica

Where did you find the replacement screen? The one I ordered that says it's for the d5200 is not the same as the one in it or in your pictures.

Heather Miller - Replica

How do you disconnect the multi-plug that is shown connected in image 4 and disconnected in image five? Does it unclip or slide out?

Amanda Bruyninckx - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 11

Ultimi 30 Giorni: 48

Tutti i Tempi: 11,758