Aggiusta la tua roba Comunità Store

Nikon D40 Mainboard Replacement

Introduzione

The mainboard controls all of the software on the Nikon D40. A faulty mainboard can cause problems that will require a new board. This guide will show you how to replace the camera's mainboard.

Cosa ti serve

  1. Nikon D40 Mainboard Replacement, Back Cover: passo 1, immagine 1 di 1

    • Remove the two visible 6.0 mm Philips #0 screws on the left and right sides of the viewfinder. These screws are highlighted in red.

    Modifica

  2. Nikon D40 Mainboard Replacement: passo 2, immagine 1 di 2 Nikon D40 Mainboard Replacement: passo 2, immagine 2 di 2

    • Remove the four 6.0 mm Philips #0 screws on the left and right sides of the camera.

    Modifica

  3. Nikon D40 Mainboard Replacement: passo 3, immagine 1 di 1

    • Remove the four highlighted 3.0 mm Philips #0 screws on the bottom of the camera.

    Modifica

  5. Nikon D40 Mainboard Replacement: passo 4, immagine 1 di 1

    • While pulling the bottom down, remove the back of the camera.

    • Be careful not to pull too hard on the back as it is connected via a ribbon cable. Be sure to disconnect this cable on the main board.

    • To disconnect the ribbon cable pull the small black tab upward and pull gently on the cable.

    Modifica

  6. Nikon D40 Mainboard Replacement, Mainboard: passo 5, immagine 1 di 2 Nikon D40 Mainboard Replacement, Mainboard: passo 5, immagine 2 di 2

    • Remove the solder connecting the red wire to the mainboard.

    Modifica

  7. Nikon D40 Mainboard Replacement: passo 6, immagine 1 di 1

    • Desolder the 4 smaller wires near the bottom of the mainboard.

    Modifica

  8. Nikon D40 Mainboard Replacement: passo 7, immagine 1 di 2 Nikon D40 Mainboard Replacement: passo 7, immagine 2 di 2

    • Use the plastic opening tool to release the ribbon cables attached to the mainboard.

    Modifica

  9. Nikon D40 Mainboard Replacement: passo 8, immagine 1 di 1

    • Remove the five 3.0mm Philips #1 screws holding the mainboard down.

    Modifica

  10. Nikon D40 Mainboard Replacement: passo 9, immagine 1 di 2 Nikon D40 Mainboard Replacement: passo 9, immagine 2 di 2

    • Lift the mainboard up to reveal the final connection.

    • Carefully detach the white cable from the board.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Autore

con 2 altri collaboratori

Joe Leija

Membro da: 01/21/14

518 Reputazione

2 Guide realizzate

Distintivi: 7

+4 altri distintivi

Team

Cal Poly, Team 6-19, Maness Winter 2014 Membro di Cal Poly, Team 6-19, Maness Winter 2014

CPSU-MANESS-W14S6G19

4 Membri

7 Guide realizzate

Un commento

What is the ordering of the small wires on the bottom? It is hard to put back together from the photos. Thanks!

Joseph Ruskiewicz - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 18

Tutti i Tempi: 4,230