Salta al contenuto principale

Ricambi

Nessuna parte specificata.

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    On the bottom right of the camera, locate the battery flap switch.
    • On the bottom right of the camera, locate the battery flap switch.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Move this switch to the right so the battery flap can flip open.
    • Move this switch to the right so the battery flap can flip open.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Slide the orange switch to the right as shown. Now the battery can be pulled out. Reverse these steps to re-install.
    • Slide the orange switch to the right as shown. Now the battery can be pulled out. Reverse these steps to re-install.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the three 3x3mm screws attached to the rear casing.
    • Remove the three 3x3mm screws attached to the rear casing.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    The panel can be identified by the wifi logo on its upper half on the camera's side.
    • The panel can be identified by the wifi logo on its upper half on the camera's side.

    • Remove the 5x3mm screw holding down the panel on the side closest to the lens.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pry the panel off from the bottom using your fingernail.
    • Pry the panel off from the bottom using your fingernail.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the 3x2mm screw underneath the panel near the top of the camera.
    • Remove the 3x2mm screw underneath the panel near the top of the camera.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the 4x3mm on the opposite side near the selector wheel. Remove the 2x2mm and 3x2mm screws underneath the a/v flap.
    • Remove the 4x3mm on the opposite side near the selector wheel.

    • Remove the 2x2mm and 3x2mm screws underneath the a/v flap.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pry the back panel away from the body of the camera, using the space you just opened up. Be careful not to damage the ribbon cable on the opposite end of the camera.
    • Pry the back panel away from the body of the camera, using the space you just opened up.

    • Be careful not to damage the ribbon cable on the opposite end of the camera.

    • A small piece of the frame of the camera may fall off, but it can be easily put back into place during reassembly.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pry up the plastic ribbon connectors on the body of the camera to release the ribbon cables. The center connector is detached by flipping the black latch up and away from the center of the camera.
    • Pry up the plastic ribbon connectors on the body of the camera to release the ribbon cables.

    • The center connector is detached by flipping the black latch up and away from the center of the camera.

    • The smaller connector is detached by flipping the tan latch up and away from the edge of the camera.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the three 3x3mm screws that attach the front casing to the bottom.
    • Remove the three 3x3mm screws that attach the front casing to the bottom.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the two 3x2 screws and two 3.5x2.5 screws attaching the rear panel to the motherboard.
    • Remove the two 3x2 screws and two 3.5x2.5 screws attaching the rear panel to the motherboard.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Lift the back panel off the motherboard. Be careful not to damage the ribbon cable that attaches the mother board to the rear panel.
    • Lift the back panel off the motherboard.

    • Be careful not to damage the ribbon cable that attaches the mother board to the rear panel.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Detach the ribbon cable from the motherboard by flipping up the latch on the ribbon connector. Note that the white ribbon connector latch flips away from the ribbon cable.
    • Detach the ribbon cable from the motherboard by flipping up the latch on the ribbon connector.

    • Note that the white ribbon connector latch flips away from the ribbon cable.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the final 4x3mm screw at the top of the camera near the lens. Remove the final 4x3mm screw at the top of the camera near the lens.
    • Remove the final 4x3mm screw at the top of the camera near the lens.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pry the front casing away from the body of the camera. Be careful not to damage the wires that attach the front panel to the motherboard.
    • Pry the front casing away from the body of the camera.

    • Be careful not to damage the wires that attach the front panel to the motherboard.

    • Short the leads on the capacitor near the flash to avoid a nasty shock when separating the casing from the body.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Unscrew the three 3x2mm screws that attach the cables to the front casing.
    • Unscrew the three 3x2mm screws that attach the cables to the front casing.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pry up the ribbon connector that connects the ribbon cable to the lens assembly. Take note that the ribbon connector pulls away from the ribbon.
    • Pry up the ribbon connector that connects the ribbon cable to the lens assembly.

    • Take note that the ribbon connector pulls away from the ribbon.

Linea Traguardo

Kevin Backers

Membro da: 26/01/2012

301 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 9-5, Regan Winter 2012 Membro di Cal Poly, Team 9-5, Regan Winter 2012

CPSU-REGAN-W12S9G5

5 Membri

12 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 3

Tutti i Tempi: 647