Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Nikon COOLPIX S610c Front Casing Replacement

Introduzione

If your front casing has come loose or needs to be replaced, follow this guid to remove your current front casing from the camera.

Cosa ti serve

  1. Nikon COOLPIX S610c Front Casing Replacement, Battery: passo 1, immagine 1 di 1

    • On the bottom right of the camera, locate the battery flap switch.

    Traduci

  2. Nikon COOLPIX S610c Front Casing Replacement: passo 2, immagine 1 di 1

    • Move this switch to the right so the battery flap can flip open.

    Traduci

  3. Nikon COOLPIX S610c Front Casing Replacement: passo 3, immagine 1 di 1

    • Slide the orange switch to the right as shown. Now the battery can be pulled out. Reverse these steps to re-install.

    Traduci

  4. Nikon COOLPIX S610c Front Casing Replacement, Rear Casing: passo 4, immagine 1 di 1

    • Remove the three 3x3mm screws attached to the rear casing.

    Traduci

  5. Nikon COOLPIX S610c Front Casing Replacement: passo 5, immagine 1 di 1

    • The panel can be identified by the wifi logo on its upper half on the camera's side.

    • Remove the 5x3mm screw holding down the panel on the side closest to the lens.

    Traduci

  6. Nikon COOLPIX S610c Front Casing Replacement: passo 6, immagine 1 di 1

    • Pry the panel off from the bottom using your fingernail.

    Traduci

  8. Nikon COOLPIX S610c Front Casing Replacement: passo 7, immagine 1 di 1

    • Remove the 3x2mm screw underneath the panel near the top of the camera.

    Traduci

  9. Nikon COOLPIX S610c Front Casing Replacement: passo 8, immagine 1 di 2 Nikon COOLPIX S610c Front Casing Replacement: passo 8, immagine 2 di 2

    • Remove the 4x3mm on the opposite side near the selector wheel.

    • Remove the 2x2mm and 3x2mm screws underneath the a/v flap.

    Traduci

  10. Nikon COOLPIX S610c Front Casing Replacement: passo 9, immagine 1 di 2 Nikon COOLPIX S610c Front Casing Replacement: passo 9, immagine 2 di 2

    • Pry the back panel away from the body of the camera, using the space you just opened up.

    • Be careful not to damage the ribbon cable on the opposite end of the camera.

    • A small piece of the frame of the camera may fall off, but it can be easily put back into place during reassembly.

    Traduci

  11. Nikon COOLPIX S610c Front Casing Replacement: passo 10, immagine 1 di 2 Nikon COOLPIX S610c Front Casing Replacement: passo 10, immagine 2 di 2

    • Pry up the plastic ribbon connectors on the body of the camera to release the ribbon cables.

    • The center connector is detached by flipping the black latch up and away from the center of the camera.

    • The smaller connector is detached by flipping the tan latch up and away from the edge of the camera.

    Traduci

  12. Nikon COOLPIX S610c Front Casing Replacement, Front Casing: passo 11, immagine 1 di 1

    • Remove the three 3x3mm screws that attach the front casing to the bottom.

    Traduci

  13. Nikon COOLPIX S610c Front Casing Replacement: passo 12, immagine 1 di 1

    • Remove the two 3x2 screws and two 3.5x2.5 screws attaching the rear panel to the motherboard.

    Traduci

  14. Nikon COOLPIX S610c Front Casing Replacement: passo 13, immagine 1 di 2 Nikon COOLPIX S610c Front Casing Replacement: passo 13, immagine 2 di 2

    • Lift the back panel off the motherboard.

    • Be careful not to damage the ribbon cable that attaches the mother board to the rear panel.

    Traduci

  15. Nikon COOLPIX S610c Front Casing Replacement: passo 14, immagine 1 di 2 Nikon COOLPIX S610c Front Casing Replacement: passo 14, immagine 2 di 2

    • Detach the ribbon cable from the motherboard by flipping up the latch on the ribbon connector.

    • Note that the white ribbon connector latch flips away from the ribbon cable.

    Traduci

  16. Nikon COOLPIX S610c Front Casing Replacement: passo 15, immagine 1 di 2 Nikon COOLPIX S610c Front Casing Replacement: passo 15, immagine 2 di 2

    • Remove the final 4x3mm screw at the top of the camera near the lens.

    Traduci

  17. Nikon COOLPIX S610c Front Casing Replacement: passo 16, immagine 1 di 2 Nikon COOLPIX S610c Front Casing Replacement: passo 16, immagine 2 di 2

    • Pry the front casing away from the body of the camera.

    • Be careful not to damage the wires that attach the front panel to the motherboard.

    • Short the leads on the capacitor near the flash to avoid a nasty shock when separating the casing from the body.

    Traduci

  18. Nikon COOLPIX S610c Front Casing Replacement: passo 17, immagine 1 di 1

    • Unscrew the three 3x2mm screws that attach the cables to the front casing.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 3 altri collaboratori

Bryan Bell

Membro da: 01/26/12

28 Reputazione

1 Guida realizzata

Distintivi: 5

+2 altri distintivi

Team

Cal Poly, Team 9-5, Regan Winter 2012 Membro di Cal Poly, Team 9-5, Regan Winter 2012

CPSU-REGAN-W12S9G5

5 Membri

12 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 1,131