Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 2 : passo 1, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    SIM Card Eject Tool
    $2.99
    Compra
    • Power off the phone, by long-pressing the power button and touching Power off.

    • Remove the SIM tray using the SIM Card Eject Tool.

    • This step is required in order to remove the back case.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    T5 Torx Screwdriver
    $5.49
    Compra
  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 3 : passo 3, immagine 2 di 3 : passo 3, immagine 3 di 3
    • Gently open the back case by prying along the edge of the cover, starting at a corner of the phone and circling around the phone using a plastic opening tool.

    • The opening process may take a few minutes. The plastic will make a light snapping noise as the back cover separates from the rest of the phone.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 2 : passo 4, immagine 2 di 2
    • Remove the two 1.8 mm Phillips screws holding down the battery connector.

    • Using a plastic opening tool, disconnect the battery cable from its socket on the motherboard.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 2 : passo 5, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    Plastic Cards
    $2.99
    Compra
    • Remove the blue tape that secures the white antenna cable to the battery.

    • Using a spudger, carefully disconnect the white antenna cable.

    • Carefully pry the battery out with a Plastic Opening Tool, starting at the top left-hand corner and working down towards the bottom right-hand corner.

    • If necessary, you can also use a plastic card to separate the battery from the metal midframe.

    • The battery is securely glued to the phone. When reinstalling the battery, press the battery firmly against the adhesive strip.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 3 : passo 6, immagine 2 di 3 : passo 6, immagine 3 di 3
    • Remove the nine 4.6 mm Phillips #000 screws. Gently lift out the plastic cover.

    • The midframe is held in with two clips, one at either side. Use a plastic spudger to release each side and gently lift up and away.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 3 : passo 7, immagine 2 di 3 : passo 7, immagine 3 di 3
    • Using a spudger, pop off the gray connector on the top right of the motherboard.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 3 : passo 8, immagine 2 di 3 : passo 8, immagine 3 di 3
    • Gently lift the audio jack upwards and to the left to remove it from the motherboard.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 2 : passo 9, immagine 2 di 2
    • The audio port will likely lift out together with the ambient light sensor rubber cap.

    • Remove the cap from the old part and move it to the new one. Ensure the cap stays in place when installing the new audio port into the phone.

Linea Traguardo

Altre 26 persone hanno completato questa guida.

Kaitlyn Jones

Membro da: 01/27/13

4.952 Reputazione

8 Guide realizzate

Team

Cal Poly, Team 3-32, Amido Winter 2013 Membro di Cal Poly, Team 3-32, Amido Winter 2013

CPSU-AMIDO-W13S3G32

4 Membri

8 Guide realizzate

Un commento

where can I order the original connector on my Nexus 4? With delivery to the Crimea.

Grateful for the answer in advance.

Konstantin - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 12

Ultimi 30 Giorni: 16

Tutti i Tempi: 22,998