Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Netgear Arlo Plastic Housing Replacement

Introduzione

How to remove the plastic housing of the camera to either replace it, or remove it to get to the internals of the camera.

Cosa ti serve

  1. Netgear Arlo Plastic Housing Replacement, Battery: passo 1, immagine 1 di 3 Netgear Arlo Plastic Housing Replacement, Battery: passo 1, immagine 2 di 3 Netgear Arlo Plastic Housing Replacement, Battery: passo 1, immagine 3 di 3

    • Locate unlock switch on underside of camera and unlock it by sliding it.

    • Once unlocked, slide the cover out and up to open the battery housing.

    Traduci

  2. Netgear Arlo Plastic Housing Replacement: passo 2, immagine 1 di 1

    • Remove all 4 of the 3.0 Volt batteries from the battery housing.

    Traduci

  3. Netgear Arlo Plastic Housing Replacement: passo 3, immagine 1 di 1

    • Inspect prongs at the bottom of the battery housing to ensure that they are not bent or broken before replacing the batteries.

    Traduci

  5. Netgear Arlo Plastic Housing Replacement, Plastic Housing: passo 4, immagine 1 di 1

    • Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

    Traduci

  6. Netgear Arlo Plastic Housing Replacement: passo 5, immagine 1 di 2 Netgear Arlo Plastic Housing Replacement: passo 5, immagine 2 di 2

    • Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

    Traduci

  7. Netgear Arlo Plastic Housing Replacement: passo 6, immagine 1 di 1

    • Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

    Traduci

  8. Netgear Arlo Plastic Housing Replacement: passo 7, immagine 1 di 3 Netgear Arlo Plastic Housing Replacement: passo 7, immagine 2 di 3 Netgear Arlo Plastic Housing Replacement: passo 7, immagine 3 di 3

    • Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.

    • Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.

    • Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

    Traduci

  9. Netgear Arlo Plastic Housing Replacement: passo 8, immagine 1 di 3 Netgear Arlo Plastic Housing Replacement: passo 8, immagine 2 di 3 Netgear Arlo Plastic Housing Replacement: passo 8, immagine 3 di 3

    • Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.

    • Remove the second screw (3.5mm) on the back of the camera to remove the second housing.

    • Once the screws are removed use an opening tool to pry back the second plastic mount.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 2 altri collaboratori

Connor Krampen

Membro da: 01/08/18

399 Reputazione

3 Guide realizzate

Distintivi: 12

+9 altri distintivi

Team

IUPUI, Team S1-G1, Freund Spring 2018 Membro di IUPUI, Team S1-G1, Freund Spring 2018

IUPUI-FREUND-S18S1G1

2 Membri

6 Guide realizzate

2 Commenti

Where can I buy replacement parts like a battery cover for Arlo

L R Hardy - Replica

Note that under the rubber cover shown in step 6 there is a USB-B port.
You can run the Arlo on a USB adapter as well.
You only need to make a hole in the battery lid or 3D print a new cover.

Bas Vijfwinkel - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 8

Tutti i Tempi: 2,324