Aggiusta la tua roba ComunitĆ  Store

Netgear Arlo Charging Port Replacement

Introduzione

This is a step-by-step guide on how to remove the charging port in a Netgear Arlo

Cosa ti serve

  1. Netgear Arlo Charging Port Replacement, Plastic Housing: passo 1, immagine 1 di 1

    • Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

    Traduci

  2. Netgear Arlo Charging Port Replacement: passo 2, immagine 1 di 2 Netgear Arlo Charging Port Replacement: passo 2, immagine 2 di 2

    • Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

    Traduci

  3. Netgear Arlo Charging Port Replacement: passo 3, immagine 1 di 1

    • Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

    Traduci

  4. Netgear Arlo Charging Port Replacement: passo 4, immagine 1 di 3 Netgear Arlo Charging Port Replacement: passo 4, immagine 2 di 3 Netgear Arlo Charging Port Replacement: passo 4, immagine 3 di 3

    • Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.

    • Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.

    • Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

    Traduci

  5. Netgear Arlo Charging Port Replacement: passo 5, immagine 1 di 3 Netgear Arlo Charging Port Replacement: passo 5, immagine 2 di 3 Netgear Arlo Charging Port Replacement: passo 5, immagine 3 di 3

    • Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.

    • Remove the second screw (3.5mm) on the back of the camera to remove the second housing.

    • Once the screws are removed use an opening tool to pry back the second plastic mount.

    Traduci

  7. Netgear Arlo Charging Port Replacement, Lens Assembly: passo 6, immagine 1 di 1

    • Remove 4 (6mm) large screws with a J00 screwdriver.

    • There are 2 on each side. This will allow you to remove the clear housing from the white housing.

    Traduci

  8. Netgear Arlo Charging Port Replacement: passo 7, immagine 1 di 2 Netgear Arlo Charging Port Replacement: passo 7, immagine 2 di 2

    • Once screws are removed, pull apart the clear housing.

    • Remove rod from camera cover.

    Traduci

  9. Netgear Arlo Charging Port Replacement: passo 8, immagine 1 di 3 Netgear Arlo Charging Port Replacement: passo 8, immagine 2 di 3 Netgear Arlo Charging Port Replacement: passo 8, immagine 3 di 3

    • Remove Large ribbon cable first to disconnect front of camera from main body.

    • Remove 4 (3.5mm) small black screws from motherboard of the camera unit.

    • Remove smaller ribbon cable from underneath yellow tape.

    Traduci

  10. Netgear Arlo Charging Port Replacement: passo 9, immagine 1 di 1

    • Once all ribbon cables are removed, remove the motherboard and camera assembly by pulling up on the black camera motherboard.

    Traduci

  11. Netgear Arlo Charging Port Replacement, Charging Port: passo 10, immagine 1 di 1

    • Remove the 2 (.135") housing screws with a JIS00 screwdriver

    Traduci

  12. Netgear Arlo Charging Port Replacement: passo 11, immagine 1 di 1

    • Remove 4 (.135") screws on the inside of the battery compartment using the JIS 00 screwdriver.

    Traduci

  13. Netgear Arlo Charging Port Replacement: passo 12, immagine 1 di 1

    • Slide the two halves apart

    Traduci

  14. Netgear Arlo Charging Port Replacement: passo 13, immagine 1 di 1

    • Remove the 2 (.135") screws holding the charging port on using the JIS 00 screwdriver.

    Traduci

  15. Netgear Arlo Charging Port Replacement: passo 14, immagine 1 di 2 Netgear Arlo Charging Port Replacement: passo 14, immagine 2 di 2

    • Remove the ribbon by prying the black ribbon holder up using the opening tool.

    • Pull the ribbon away from the charging port.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 1 altro collaboratore

Brian Johnson

Membro da: 03/21/18

187 Reputazione

1 Guida realizzata

Distintivi: 5

+2 altri distintivi

Team

IUPUI, Team S2-G1, Freund Spring 2018 Membro di IUPUI, Team S2-G1, Freund Spring 2018

IUPUI-FREUND-S18S2G1

2 Membri

4 Guide realizzate

4 Commenti

Great Job, Thank you!

Bob Olive Sr - Replica

Great thanks where did you get the replacement cable please thanks Mike

mikewalters1951 - Replica

where did you get the replacement cable please thanksĀ  BOB

robertwatkins61 - Replica

Any hints on where the new port came from? I have the baby monitor and the port is cheap rubbish and needs replacing. Thanks

David - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 8

Ultimi 30 Giorni: 56

Tutti i Tempi: 5,185