Introduzione

Use this guide to detach the right shell.

Parti

Nessuna parte richiesta.

Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.
  • Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

  • Remove the two 9.0 mm Phillips screws securing the battery compartment.

  • Slide the battery compartment out.

Aggiungi Commento

Remove the five 9.0 mm Phillips screws securing the trigger.
  • Remove the five 9.0 mm Phillips screws securing the trigger.

Aggiungi Commento

  • Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

  • Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

Aggiungi Commento

  • Remove both halves of the ring by tugging on it upwards until the lock gets freed.

  • This requires quite a bit of force and if you are not careful, you may break the plastic lock.

Aggiungi Commento

  • Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

Aggiungi Commento

  • Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

Aggiungi Commento

  • Remove the three 9.0 mm Phillips screws holding together the firing chamber.

  • Remove the single 7.0 mm Phillips screw below the barrel.

  • Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

Aggiungi Commento

  • Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

Aggiungi Commento

  • Remove the two 9.0 mm Phillips screws holding together the handle.

  • Remove the plastic cover of the handle.

Aggiungi Commento

  • Insert one plastic opening tool inside one side of the orange part depicted in the picture.

  • Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

Aggiungi Commento

  • Pull one end of the handle away from the orange latch.

  • Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

Aggiungi Commento

  • Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

  • Completely remove the left shell from the rest of the Nerf Gun.

Aggiungi Commento

  • Remove the cartridge support.

Aggiungi Commento

  • Remove the handle crank.

Aggiungi Commento

  • Remove the clear plastic barrel cover.

Aggiungi Commento

  • Remove the firing pin.

Aggiungi Commento

  • Lift the trigger mechanism out of the shell.

  • You cannot fully remove the trigger mechanism just yet. However taking it out of the shell helps in later steps.

Aggiungi Commento

  • Remove the two 9.0 mm Phillips screws.

Aggiungi Commento

  • To remove the motor and trigger mechanism you have to detach these two wires which are glued to the shell.

  • Hold close to the wire and pull upward slowly.

  • If you pull too quickly you can potentially damage the wire.

Aggiungi Commento

  • Once all the pieces are removed the right shell should be fully accessible.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

sage

Membro da: 24/01/2014

301 Reputazione

3 Guide realizzate

Team

Cal Poly, Team 13-13, Regan Winter 2014 Membro di Cal Poly, Team 13-13, Regan Winter 2014

CPSU-REGAN-W14S13G13

4 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 37

Tutti i Tempi: 2,346