Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Neato Botvac D8000 Wheel Replacement

Cosa ti serve

  1. Neato Botvac D8000 Wheel Replacement, Brushes: passo 1, immagine 1 di 1
    • Place the vacuum on its back so the brushes are visible.

  2. Neato Botvac D8000 Wheel Replacement: passo 2, immagine 1 di 3 Neato Botvac D8000 Wheel Replacement: passo 2, immagine 2 di 3 Neato Botvac D8000 Wheel Replacement: passo 2, immagine 3 di 3
    • Remove the four 10 mm screws with a Torx T10 screwdriver.

  3. Neato Botvac D8000 Wheel Replacement: passo 3, immagine 1 di 2 Neato Botvac D8000 Wheel Replacement: passo 3, immagine 2 di 2
    • Remove the rotary brush simply by grabbing it firmly and pulling it off.

    • Once you have removed your rotary brush and 4 bolts, you can easy remove the brush guard.

  4. Neato Botvac D8000 Wheel Replacement: passo 4, immagine 1 di 2 Neato Botvac D8000 Wheel Replacement: passo 4, immagine 2 di 2
    • Remove the brush by simply pulling it out.

    • From there you can clean it or replace the brush with a new one.

  5. Neato Botvac D8000 Wheel Replacement, Top Face Panel: passo 5, immagine 1 di 1
    • Grab the rear bumper with both hands on either side.

  6. Neato Botvac D8000 Wheel Replacement: passo 6, immagine 1 di 2 Neato Botvac D8000 Wheel Replacement: passo 6, immagine 2 di 2
    • Firmly pull the bumper forward at a steady pace.

    • When pulling the bumper forward avoid being too rough because the bumper might break.

  7. Neato Botvac D8000 Wheel Replacement: passo 7, immagine 1 di 2 Neato Botvac D8000 Wheel Replacement: passo 7, immagine 2 di 2
    • Looking from above, remove the two 11mm screws with a Torx T10 screwdriver.

  8. Neato Botvac D8000 Wheel Replacement: passo 8, immagine 1 di 3 Neato Botvac D8000 Wheel Replacement: passo 8, immagine 2 di 3 Neato Botvac D8000 Wheel Replacement: passo 8, immagine 3 di 3
    • Place the robot on its back and remove the six 11mm screws using a Torx T10 screwdriver.

  9. Neato Botvac D8000 Wheel Replacement: passo 9, immagine 1 di 3 Neato Botvac D8000 Wheel Replacement: passo 9, immagine 2 di 3 Neato Botvac D8000 Wheel Replacement: passo 9, immagine 3 di 3
    • Push the clips, located in the back side, inward.

    • Gently lift up the top cover until you can see the wires. Then gently un-clip all the wires.

    • When you lift the top cover be careful because the wires are thin and fragile.

  10. Neato Botvac D8000 Wheel Replacement: passo 10, immagine 1 di 1
    • Once you have carefully removed the wire clip; you can fully remove the top cover.

  11. Neato Botvac D8000 Wheel Replacement, Wheel: passo 11, immagine 1 di 3 Neato Botvac D8000 Wheel Replacement, Wheel: passo 11, immagine 2 di 3 Neato Botvac D8000 Wheel Replacement, Wheel: passo 11, immagine 3 di 3
    • Locate the screws that mount the wheel extension to the Robot.

    • Unscrew the four 11mm screws indicated with a Torx T10 screwdriver to remove the frame.

    • Make sure to remove the metallic weight. However, this does not require the removal of any screws.

  12. Neato Botvac D8000 Wheel Replacement: passo 12, immagine 1 di 3 Neato Botvac D8000 Wheel Replacement: passo 12, immagine 2 di 3 Neato Botvac D8000 Wheel Replacement: passo 12, immagine 3 di 3
    • Delicately lift up the frame holding the laser. This will access the wheels.

    • Detach the wheel wires that are connected to the motherboard.

    • Once the wires are detached, the wheel are free from their casing.

  13. Neato Botvac D8000 Wheel Replacement: passo 13, immagine 1 di 2 Neato Botvac D8000 Wheel Replacement: passo 13, immagine 2 di 2
    • Use a Torx T15 screwdriver to remove the 32.5mm screw.

    • Finally, just hold and separate the wheel from its axle.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 9

Ultimi 30 Giorni: 26

Tutti i Tempi: 3,486