Aggiusta la tua roba

Diritto alla Riparazione

Store

NERF Doomlands 2169 Lawbringer Blaster Repair Spring Replacement

Scritto Da: Georgia Slack (e 2 altri collaboratori)
  • Commenti: 0
  • Preferiti: 1

Difficoltà

Moderato

Passi

12

Tempo Necessario

Suggerisci un tempo??

Sezioni

1

Contrassegni

5

Action Shots

Foto Azione

Passa all'azione, eroe! Questa guida ha bisogno di immagini che meglio illustrano come eseguire azioni specifiche.

Scenic Route

Strada Panoramica

Il procedimento riportato in questa guida non è il più efficace per effettuare il lavoro, ma in alcune circostanze può ancora tornare utile.

Needs Better Images

Necessarie Immagini Migliori

Delle foto più belle renderanno migliore questa guida. Contribuisci scattando, modificando o caricando immagini nuove!

Step Trimmer

Tagliatore di Passi

Questa guida contiene passaggi inutili. Tagliali, sii più conciso!

Missing Details

Dettagli Mancanti

Alcuni dettagli di questa guida sono mancanti. Aiuta gli utenti aggiungendo strumenti, livello di difficoltà o tempo di esecuzione.

  1. Locate and remove all sixteen screws of the outer case and gently remove it, avoiding any damage. Locate and remove all sixteen screws of the outer case and gently remove it, avoiding any damage.

    • Locate and remove all sixteen screws of the outer case and gently remove it, avoiding any damage.

    Modifica

  2. Remove the three screws attached to the trigger mechanism of the gun.

    • Remove the three screws attached to the trigger mechanism of the gun.

    • Be careful when removing the rotating cartridge from the case, as the fulcrum attaching it to the trigger mechanism will fall out!

    Modifica

  3. Remove the exterior spring from the sliding mechanism and rotate the gun to the opposite side.

    • Remove the exterior spring from the sliding mechanism and rotate the gun to the opposite side.

    Modifica

  4. Remove the three screws holding the trigger plate in place, then remove the plate carefully. Remove the three screws holding the trigger plate in place, then remove the plate carefully.

    • Remove the three screws holding the trigger plate in place, then remove the plate carefully.

    Modifica

  6. Remove the spring and trigger mechanism from the gun, and set aside.

    • Remove the spring and trigger mechanism from the gun, and set aside.

    Modifica

  7. Carefully slide out the big spring and fit in your replacement (thin-coil end coiled around the orange plastic).

    • Carefully slide out the big spring and fit in your replacement (thin-coil end coiled around the orange plastic).

    • This is where the spring load mechanism is located. Be cautious not to damage. If the spring separates from the gun, reattach it using a screwdriver end.

    Modifica

  8. Keep tension on the spring and begin sliding the new coil spring into the trigger mechanism.

    • Keep tension on the spring and begin sliding the new coil spring into the trigger mechanism.

    • Make sure the orange slide is above the spring. A second set of hands would be useful during this step.

    Modifica

  9. Reconnect the spring to the orange slider, and connect the orange slider to the grey hook.

    • Reconnect the spring to the orange slider, and connect the orange slider to the grey hook.

    Modifica

  10. Slide the orange supporting piece into the crevice below the air chamber.

    • Slide the orange supporting piece into the crevice below the air chamber.

    Modifica

  11. Slide the rotating cartridge back into place.

    • Slide the rotating cartridge back into place.

    Modifica

  12. Carefully reassemble the NERF Lawbringer in the same order you took it apart. Carefully reattach the three screws that seal the air chamber.

    • Carefully reassemble the NERF Lawbringer in the same order you took it apart. Carefully reattach the three screws that seal the air chamber.

    Modifica

  13. Reattach the other plastic half of the gun. Tighten the screws and you're done.

    • Reattach the other plastic half of the gun. Tighten the screws and you're done.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 2 altri collaboratori

Georgia Slack

Membro da: 13/10/2016

113 Reputazione

1 Guida realizzata

Distintivi: 5

+2 altri distintivi

Team

University of Maine, Team 1-5, Diaz Fall 2016 Membro di University of Maine, Team 1-5, Diaz Fall 2016

UMAINE-DIAZ-F16S1G5

2 Membri

1 Guida realizzata

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 17

Tutti i Tempi: 634