Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Motorola RIZR Z3 Screen Replacement

Introduzione

Guide to installing a new screen.

Cosa ti serve

  1. Motorola RIZR Z3 Screen Replacement, Battery: passo 1, immagine 1 di 2 Motorola RIZR Z3 Screen Replacement, Battery: passo 1, immagine 2 di 2

    • Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.

    Traduci

  2. Motorola RIZR Z3 Screen Replacement: passo 2, immagine 1 di 2 Motorola RIZR Z3 Screen Replacement: passo 2, immagine 2 di 2

    • Tilt the battery by lifting at the exposed notch.

    • Slide the battery out of its casing.

    Traduci

  3. Motorola RIZR Z3 Screen Replacement, Motherboard: passo 3, immagine 1 di 1

    • Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.

    Traduci

  4. Motorola RIZR Z3 Screen Replacement: passo 4, immagine 1 di 2 Motorola RIZR Z3 Screen Replacement: passo 4, immagine 2 di 2

    • Use a plastic opening tool to lift the plastic casing.

    • Pull the plastic casing directly away from the phone.

    Traduci

  5. Motorola RIZR Z3 Screen Replacement: passo 5, immagine 1 di 1

    • Lift the black rubber loudspeaker housing up and out of the plastic casing.

    Traduci

  7. Motorola RIZR Z3 Screen Replacement: passo 6, immagine 1 di 2 Motorola RIZR Z3 Screen Replacement: passo 6, immagine 2 di 2

    • Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.

    • Caution: Remove carefully, if broken, the phone will not be able to make calls.

    Traduci

  8. Motorola RIZR Z3 Screen Replacement: passo 7, immagine 1 di 2 Motorola RIZR Z3 Screen Replacement: passo 7, immagine 2 di 2

    • Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.

    • Caution: Remove carefully, if broken, the phone will not function properly.

    Traduci

  9. Motorola RIZR Z3 Screen Replacement: passo 8, immagine 1 di 2 Motorola RIZR Z3 Screen Replacement: passo 8, immagine 2 di 2

    • Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.

    • Caution: Do this gently Unclipping too fast may cause damage to your phone.

    Traduci

  10. Motorola RIZR Z3 Screen Replacement, Screen: passo 9, immagine 1 di 1

    • Turn the phone to the front.

    • Push the keypad out through the plastic casing.

    Traduci

  11. Motorola RIZR Z3 Screen Replacement: passo 10, immagine 1 di 1

    • Turn the phone to the side.

    • Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.

    Traduci

  12. Motorola RIZR Z3 Screen Replacement: passo 11, immagine 1 di 1

    • Use a T4 screwdriver to unscrew the two .15 inch screws holding the LCD to the faceplate.

    Traduci

  13. Motorola RIZR Z3 Screen Replacement: passo 12, immagine 1 di 3 Motorola RIZR Z3 Screen Replacement: passo 12, immagine 2 di 3 Motorola RIZR Z3 Screen Replacement: passo 12, immagine 3 di 3

    • Use a spudger to pry the plastic screen casing partially up from the LCD unit.

    • Use the spudger to pry the ribbon cable away from its clip on the LCD unit.

    • Caution: If the LCD will not function properly if this ribbon cable is broken.

    • Pull the plastic screen casing directly away from the LCD unit.

    Traduci

  14. Motorola RIZR Z3 Screen Replacement: passo 13, immagine 1 di 1

    • Turn the plastic screen casing over.

    • Carefully use a spudger to push the on the two clips holding the navigational pad in place.

    • You may have to pry the pad away from the plastic screen casing with the spudger.

    Traduci

  15. Motorola RIZR Z3 Screen Replacement: passo 14, immagine 1 di 2 Motorola RIZR Z3 Screen Replacement: passo 14, immagine 2 di 2

    • Use a plastic opening tool to pry the screen up, being mindful of the glue holding the screen to its casing.

    • Pull the screen directly away from the casing.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 5 altri collaboratori

Brooke Shuford

Membro da: 10/10/11

65 Reputazione

3 Guide realizzate

Distintivi: 7

+4 altri distintivi

Team

Cal Poly, Team 5-34, Amido Fall 2011 Membro di Cal Poly, Team 5-34, Amido Fall 2011

CPSU-AMIDO-F11S5G34

4 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 2

Tutti i Tempi: 1,354