Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a SIM eject tool, bit, or a straightened paperclip into the hole in the SIM tray, located at the top left edge of the phone.
-
Push firmly to eject the tray.
-
Pull the tray straight out to remove the tray.
-
-
-
Scalda i bordi dello schermo del tuo Motorola Moto Z2 Play per 2/3 minuti con una pistola termica. Imposta la temperatura a 85° C e stai attento non tenere troppo la pistola su un solo punto per evitare di danneggiare il pannello LCD. Lo schermo dovrebbe essere molto caldo, ma non doloroso da toccare. Riscalda se necessario.
-
-
-
Trova il cavo a nastro in basso a destra nel telefono.
-
Se presente, rimuovi il nastro Kapton (arancione) che copre il connettore del cavo.
-
Solleva verso l'alto la piccola linguetta di blocco sul connettore ZIF e utilizza delle pinzette per far scivolare il cavo dritto fuori dalla sua presa.
-
-
-
-
Usando delle pinzette, rimuovi il nastro arancione disposto in basso a destra del telefono.
-
-
-
Solleva il nastro nero e fai scorrere una scheda di plastica sotto la batteria.
-
Allinea la scheda parallelamente al lato lungo della batteria e sotto di essa.
-
Incunea la scheda ancora più sotto la batteria.
-
Solleva verso l'altro la scheda per favorire il distacco della batteria dall'adesivo.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three silver 2.6 mm T3 Torx screws on the speaker shell at the top of the phone with a screwdriver by turning counterclockwise.
-
Remove the four black 3.5 mm T3 Torx screws on the speaker shell at the top of the phone with a screwdriver by turning counterclockwise.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up the silver metallic tape using the tweezers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift gently to completely remove speaker housing using tweezers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place the housing upside down in order to continue working.
-
Pry the speaker from the housing with a plastic opening tool.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the seven silver 2.6 mm T3 Torx screws on the black battery cable cover at the bottom of the phone with a screwdriver by turning counterclockwise.
-
Remove the single black 3.5 mm T3 Torx screw on the black battery cable cover at the bottom of the phone with a screwdriver by turning counterclockwise.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the battery cover with tweezers starting on the right side slightly to dislodge the cover.
-
Lift the battery cover with tweezers from the left side slightly to dislodge the cover.
-
Remove the battery cover with tweezers by solidly gripping the left side of the cover and lifting up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Tilt the front of the black audio jack up with tweezers.
-
Lift the audio jack out of its housing with tweezers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three black 2.6 mm T3 Torx screws on the motherboard panel at the side of the phone with a screwdriver by turning counterclockwise.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place a plastic opening tool under the edge of the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the motherboard from the right edge like a book towards the left.
-
Identify the connector on the top left of the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Detach the connection on the bottom of the motherboard.
-
Annulla: non ho completato questa guida.
Un'altra persona ha completato questa guida.
Un commento
Dear sir
I need Moto Z2 play mother board for golden colour hand set want to know the price