Aggiusta la tua roba Comunità Store

Motorola Moto X4 Display Assembly Replacement

Introduzione

Be sure to completely power down your Moto X4 before you use the iOpener to open the phone.

Cosa ti serve

  1. Motorola Moto X4 Display Assembly Replacement, Display Assembly: passo 1, immagine 1 di 2 Motorola Moto X4 Display Assembly Replacement, Display Assembly: passo 1, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    Tesa 61395 Tape
    $5.99
    Compra

    • Your Moto X4 may not be water resistant after reassembly.

    • Before beginning the disassembly of your Moto X4, discharge the battery below 25%. A charged lithium-ion battery can catch fire or explode if accidentally punctured.

    • Use an iOpener or a heat gun to heat up all four edges of the display until it's slightly too hot to touch, in order to soften the adhesive holding it in place.

    • Slide a thin pry tool such as an opening pick or playing card underneath the edge of the display, and work it carefully around the entire perimeter of the phone to slice through the adhesive.

    • Don't insert your tool more than a few millimeters, or you may damage the display cables on the right edge.

    • Open the display from the left edge, and swing it to the right. Don't try to fully detach it yet.

    • When your repair is complete, thoroughly remove all the old adhesive surrounding the display, and clean the adhered surfaces with isopropyl alcohol and a lint-free cloth. Install your new display with a strong double-sided tape, such as Tesa 61395.

    Traduci

  3. Motorola Moto X4 Display Assembly Replacement: passo 2, immagine 1 di 3 Motorola Moto X4 Display Assembly Replacement: passo 2, immagine 2 di 3 Motorola Moto X4 Display Assembly Replacement: passo 2, immagine 3 di 3

    • Insert the spudger under the black tab by the top connector, then pry it up.

    • Grab the cable and gently disconnect the screen from the rest of the Moto X4.

    Traduci

  4. Motorola Moto X4 Display Assembly Replacement: passo 3, immagine 1 di 3 Motorola Moto X4 Display Assembly Replacement: passo 3, immagine 2 di 3 Motorola Moto X4 Display Assembly Replacement: passo 3, immagine 3 di 3

    • Insert the spudger under the black tab by the bottom connector, then pry it up.

    • Grab the cable and gently disconnect the screen from the rest of the Moto X4.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 23 persone hanno completato questa guida.

Autore

con 11 altri collaboratori

Brian Buchanan

Membro da: 01/24/18

1.047 Reputazione

5 Guide realizzate

Distintivi: 15

+12 altri distintivi

Team

Cal Poly, Team S18-G4, Livingston Winter 2018 Membro di Cal Poly, Team S18-G4, Livingston Winter 2018

CPSU-LIVINGSTON-W18S18G4

4 Membri

13 Guide realizzate

8 Commenti

This guide really only covers screen removal, and should detail replacing the screen as advertised. Here are a few more steps that should be added:

1. Transferring old hardware to the new screen (seals, filters, fingerprint sensor, & the grey carbon mat.

2. Cleaning up old adhesive.

3. Applying new adhesive, whether it’s the one-piece that ifixit carries (recommended), or Tesa tape.

4. Installing the new display assembly

Andrew Parker - Replica

Is it possible to remove and replace only the glass? Can I do that without removing the whole LCD screen and avoid disconnecting/reconnecting wires?

Drew S - Replica

Hi Drew,

I haven’t tried, but I think it is possible to do a glass-only repair for this LCD screen, as long as you have the necessary tools and bonding adhesives. You would still have to deal with the fingerprint sensor, which is sealed onto the glass.

Arthur Shi -

I noticed the fingerprint sensor not being quite as low on the right edge after this. Also, I think it has a bit of “give” now when I press on it with a thumbnail. If the tips of my thumbs weren't so dry right now I might not have noticed, though.

Chris Young - Replica

Hey Chris,

Did you add adhesive to the fingerprint sensor, if you didn't add some adhesive it may have some play, as most things need to be glued in place, and you could have forgotten to add some new adhesive.

Dominik Rodriguez -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 14

Ultimi 30 Giorni: 62

Tutti i Tempi: 17,104