Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Motorola Droid Turbo 2 Midframe Replacement

Cosa ti serve

  1. Motorola Droid Turbo 2 Midframe Replacement, Midframe: passo 1, immagine 1 di 3 Motorola Droid Turbo 2 Midframe Replacement, Midframe: passo 1, immagine 2 di 3 Motorola Droid Turbo 2 Midframe Replacement, Midframe: passo 1, immagine 3 di 3
    • Power off your phone before you begin working.

    • Insert a SIM eject tool, SIM eject bit, or a straightened paperclip into the small hole in the SIM card tray.

    • Press to eject the tray.

    • Remove the SIM card tray assembly from the phone.

  2. Motorola Droid Turbo 2 Midframe Replacement: passo 2, immagine 1 di 1
    • Heat an iOpener and apply it to the top edge of the phone for a minute.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

  3. Motorola Droid Turbo 2 Midframe Replacement: passo 3, immagine 1 di 2 Motorola Droid Turbo 2 Midframe Replacement: passo 3, immagine 2 di 2
    • Angle an opening pick and firmly press so that it slips under the back cover.

    • Depending on the age of the phone, this can be difficult. Additional heating with the iOpener may help. You can pry carefully with a metal spudger to create a gap for the opening pick.

  4. Motorola Droid Turbo 2 Midframe Replacement: passo 4, immagine 1 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 4, immagine 2 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 4, immagine 3 di 3
    • Slide the opening pick along the top edge of the phone to break up the adhesive.

    • Use the pick to release the deeper areas but avoid slicing through the camera bezel area.

  5. Motorola Droid Turbo 2 Midframe Replacement: passo 5, immagine 1 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 5, immagine 2 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 5, immagine 3 di 3
    • Repeat the iOpener heating and slicing procedures for the remaining three sides.

    • Make sure to cut into the deeper areas as the back cover is held on by a large adhesive surface.

  6. Motorola Droid Turbo 2 Midframe Replacement: passo 6, immagine 1 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 6, immagine 2 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 6, immagine 3 di 3
    • Once you have cut through the adhesive, slowly peel the back cover away from the frame.

    • Remove the back cover.

    • During reassembly, follow this rear cover adhesive guide to properly apply the pre-cut adhesive strip.

  7. Motorola Droid Turbo 2 Midframe Replacement: passo 7, immagine 1 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 7, immagine 2 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 7, immagine 3 di 3
    • Insert an opening pick under the flash connector rubber cover and pry forward to remove it.

    • To reinstall the cover, align the cover and use your finger to push it forward into place.

  8. Motorola Droid Turbo 2 Midframe Replacement: passo 8, immagine 1 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 8, immagine 2 di 3 Motorola Droid Turbo 2 Midframe Replacement: passo 8, immagine 3 di 3
    • Use the point of a spudger to pry up and remove the coil connector rubber cover.

    • To reinstall the cover, align the cover and use your finger to push it forward into place.

  9. Motorola Droid Turbo 2 Midframe Replacement: passo 9, immagine 1 di 2 Motorola Droid Turbo 2 Midframe Replacement: passo 9, immagine 2 di 2
    • Use the point of a spudger to pry up and disconnect the flash connector.

    • To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

  10. Motorola Droid Turbo 2 Midframe Replacement: passo 10, immagine 1 di 2 Motorola Droid Turbo 2 Midframe Replacement: passo 10, immagine 2 di 2
    • Use the point of a spudger to pry up and disconnect the wireless charging coil connector.

  11. Motorola Droid Turbo 2 Midframe Replacement: passo 11, immagine 1 di 1
    • Remove the following T3 screws securing the midframe:

    • Thirteen 3.1 mm black screws

    • Four 4.3 mm silver screws

  12. Motorola Droid Turbo 2 Midframe Replacement: passo 12, immagine 1 di 2 Motorola Droid Turbo 2 Midframe Replacement: passo 12, immagine 2 di 2
    • Insert an opening pick along the frame seam and twist slightly to release the midframe from the phone.

  13. Motorola Droid Turbo 2 Midframe Replacement: passo 13, immagine 1 di 2 Motorola Droid Turbo 2 Midframe Replacement: passo 13, immagine 2 di 2
    • Remove the midframe from the phone.

    • You can tape over the side buttons to prevent them from falling out during your repair.

    • If the buttons fall out of the midframe, reinsert them in the orientation as shown before you reinstall the midframe.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Motorola Moto Droid Turbo 2 Answers community for troubleshooting help.

Altre 4 persone hanno completato questa guida.

Arthur Shi

Membro da: 01/03/18

248.568 Reputazione

503 Guide realizzate

Team

iFixit Membro di iFixit

Staff

136 Membri

16.579 Guide realizzate

3 Commenti

Other than the comments I left above, I felt this was a nice simple-to-follow guide that gives me confidence to try this myself.

If you fix the items listed above, it will be perfect.

Thanks!

pj.catania - Replica

Good post and the extra comments help.

Jane Doe - Replica

Where can I buy a good T3 screwdriver?

I have tried 3 brands and the screwdriver rounds off instead of removing the screw.

David Peterson - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 4

Tutti i Tempi: 7,559