Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Introduzione

Use this guide to remove the motherboard assembly of the Motorola Moto C.

  1. Power off your phone before beginning disassembly. Insert a thumbnail, or spudger, into the notch on the bottom right corner to start separating the phone unit from the back cover. Move it to the bottom left corner and pry the phone unit out of the back cover until you can get a good grip.
    • Power off your phone before beginning disassembly.

    • Insert a thumbnail, or spudger, into the notch on the bottom right corner to start separating the phone unit from the back cover.

    • Move it to the bottom left corner and pry the phone unit out of the back cover until you can get a good grip.

  2. Lift the phone out of the back cover. Lift the phone out of the back cover.
    • Lift the phone out of the back cover.

  3. Use a finger or spudger to lever the battery out of its recess and remove it. Use a finger or spudger to lever the battery out of its recess and remove it. Use a finger or spudger to lever the battery out of its recess and remove it.
    • Use a finger or spudger to lever the battery out of its recess and remove it.

  4. Remove the six 3.5 mm long Torx T5 screws.
    • Remove the six 3.5 mm long Torx T5 screws.

  5. Insert an opening pick between the cover and the motherboard near the SIM 2 slot where the power buttons are located. Slide and twist the opening pick to pry open the plastic clips securing the cover.
    • Insert an opening pick between the cover and the motherboard near the SIM 2 slot where the power buttons are located.

    • Slide and twist the opening pick to pry open the plastic clips securing the cover.

  6. Slide an opening pick between the cover and the motherboard on the opposite side next to the SD card slot. Twist the opening pick to pry open the plastic clips securing the cover.
    • Slide an opening pick between the cover and the motherboard on the opposite side next to the SD card slot.

    • Twist the opening pick to pry open the plastic clips securing the cover.

  7. SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits

    SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits
  8. Remove the motherboard cover. Remove the motherboard cover.
    • Remove the motherboard cover.

  9. Remove the three 2.5 mm long T5 Torx screws.
    • Remove the three 2.5 mm long T5 Torx screws.

  10. Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located on the bottom left of the motherboard. Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located on the bottom left of the motherboard.
    • Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located on the bottom left of the motherboard.

  11. Use a pair of tweezers to pull the power and volume button flex cable out of the ZIF connector. Fold the power and volume button flex cable out of the way.
    • Use a pair of tweezers to pull the power and volume button flex cable out of the ZIF connector.

    • Fold the power and volume button flex cable out of the way.

  12. Use the flat end of a spudger to pry up and disconnect the display flex cable located at the bottom of the motherboard. Use the flat end of a spudger to pry up and disconnect the display flex cable located at the bottom of the motherboard.
    • Use the flat end of a spudger to pry up and disconnect the display flex cable located at the bottom of the motherboard.

  13. Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located at the top  of the motherboard next to the rear camera. Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located at the top  of the motherboard next to the rear camera.
    • Use the tip of an opening pick to pry up and open the black lever of the ZIF connector located at the top of the motherboard next to the rear camera.

  14. Use a pair of tweezers to pull the digitizer flex cable out of the ZIF connector. Use a pair of tweezers to pull the digitizer flex cable out of the ZIF connector.
    • Use a pair of tweezers to pull the digitizer flex cable out of the ZIF connector.

  15. Prepare an iOpener and apply it to the upper half of the display for at least two minutes to loosen the adhesive beneath the vibration motor and the rear facing camera.
    • Prepare an iOpener and apply it to the upper half of the display for at least two minutes to loosen the adhesive beneath the vibration motor and the rear facing camera.

  16. Don't try to remove the motherboard all the way yet. The antenna cable is still connected to its rear side. Use a spudger to carefully lift the motherboard until you can get a good grip. Avoid to damage the cables next to the motherboard.
    • Don't try to remove the motherboard all the way yet. The antenna cable is still connected to its rear side.

    • Use a spudger to carefully lift the motherboard until you can get a good grip. Avoid to damage the cables next to the motherboard.

  17. Fold the motherboard over the battery cavity to access the coaxial cable connectors. Fold the motherboard over the battery cavity to access the coaxial cable connectors. Fold the motherboard over the battery cavity to access the coaxial cable connectors.
    • Fold the motherboard over the battery cavity to access the coaxial cable connectors.

  18. Use a pair of tweezers to pry up and disconnect the antenna cable from the back of the motherboard. Use a pair of tweezers to pry up and disconnect the antenna cable from the back of the motherboard.
    • Use a pair of tweezers to pry up and disconnect the antenna cable from the back of the motherboard.

  19. Remove the motherboard.
    • Remove the motherboard.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Dominik Schnabelrauch

Membro da: 23/11/2016

71.096 Reputazione

320 Guide realizzate

Team

iFixit Membro di iFixit

Community

128 Membri

12.985 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 13

Ultimi 30 Giorni: 41

Tutti i Tempi: 473