Aggiusta la tua roba

Diritto alla Riparazione

Store

Motherboard

Scritto Da: Andrew (e 8 altri collaboratori)
  • Commenti: 0
  • Preferiti: 0
  • Completamenti: 2

Difficoltà

Moderato

Passi

9

Tempo Necessario

5 - 10 minuti

Sezioni

2

Contrassegni

2

Grammar Police

Vigilanza sulla Grammatica

Adotta il tuo insegnante di inglese interno e contribuisci a migliorare la grammatica di questa guida!

Needs Better Images

Necessarie Immagini Migliori

Delle foto più belle renderanno migliore questa guida. Contribuisci scattando, modificando o caricando immagini nuove!

Introduzione

This guide will help locate the motherboard for removal and/or repair.

Strumenti

Acquista questi strumenti

Parti

Nessuna parte specificata.

  1. Flip over the phone and then slide down the back cover with your thumb.

    • Flip over the phone and then slide down the back cover with your thumb.

    Traduci

  2. Lever out the battery from the phone using your thumb.

    • Lever out the battery from the phone using your thumb.

    Traduci

  3. Use a plastic opening tool to pry out the two tabs on the top corners of the battery compartment. Use a plastic opening tool to pry out the two tabs on the top corners of the battery compartment.

    • Use a plastic opening tool to pry out the two tabs on the top corners of the battery compartment.

    Traduci

  4. APRI TUTTE LE SCHEDE

    Kit espansione RAM per Mac

    Acquista Kit

    Abbastanza RAM
    Per tutte le schede

    Acquista Kit

  5. Gently pull off hinge cap piece from the the top of the phone.

    • Gently pull off hinge cap piece from the the top of the phone.

    Traduci

  6. Using a T6 Torx Screwdriver, remove the four 7.62mm screws around the corners of the battery compartment.

    • Using a T6 Torx Screwdriver, remove the four 7.62mm screws around the corners of the battery compartment.

    Traduci

  7. Open the phone and turn it on its side. Using a plastic opening tool, run along the seam located around the sides of the phone to pop the clips holding the casing to the frame.

    • Open the phone and turn it on its side.

    • Using a plastic opening tool, run along the seam located around the sides of the phone to pop the clips holding the casing to the frame.

    Traduci

  8. Using your hand, gently pull of the back panel from the bottom half of the phone.

    • Using your hand, gently pull of the back panel from the bottom half of the phone.

    Traduci

  9. Close the phone and place it on a flat surface.

    • Close the phone and place it on a flat surface.

    • Using a plastic opening tool or your finger, lift up the motherboard from the bottom casing.

    • Be careful when pulling up the board, as there is still a ribbon cable attached to the back of the board.

    Traduci

  10. On the underside of the motherboard, find the ribbon cable that attaches the board to the rest of the phone.

    • On the underside of the motherboard, find the ribbon cable that attaches the board to the rest of the phone.

    • Using a plastic opening tool, slowly detach the ribbon cable connector, then pull the motherboard away from the frame.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 8 altri collaboratori

Andrew

Membro da: 04/10/2010

397 Reputazione

4 Guide realizzate

Distintivi: 8

+5 altri distintivi

Team

Cal Poly, Team 4-46, Amido Fall 2010 Membro di Cal Poly, Team 4-46, Amido Fall 2010

CPSU-AMIDO-F10S4G46

4 Membri

14 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 4

Tutti i Tempi: 273