Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement

Cosa ti serve

  1. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: passo 1, immagine 1 di 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: passo 1, immagine 2 di 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: passo 1, immagine 3 di 3
    • Before you begin, make sure to power off and unplug the device from the outlet.

    • If the clear water pump hose is connected, remove it now.

    • Loosen the plastic knob holding the saw's cutting head in place.

    • Lower the cutting head while keeping it steady.

  2. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 2, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 2, immagine 2 di 2
    • Unscrew the knob.

    • Remove it from the cutting head.

  3. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 3, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 3, immagine 2 di 2
    • Loosen the plastic knob holding the blade cover in place.

  4. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 4, immagine 1 di 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 4, immagine 2 di 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 4, immagine 3 di 3
    • Loosen the wing nut on the blade cover pivot shaft.

    • Remove the wing nut and accompanying washer.

  5. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 5, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 5, immagine 2 di 2
    • Pivot the blade cover up and pull it off the shaft.

  6. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: passo 6, immagine 1 di 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: passo 6, immagine 2 di 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: passo 6, immagine 3 di 3
    • Insert the provided spanner wrench into one of the four tightening holes on the inner flange behind the blade.

    • Use the the provided nut wrench to loosen the hex nut while providing counterforce with the spanner wrench.

  7. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 7, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 7, immagine 2 di 2
    • Remove the hex nut.

    • Remove the outer flange.

  8. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 8, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 8, immagine 2 di 2
    • Remove the cutting blade.

    • The blade can be sharp, so handle with care.

  9. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: passo 9, immagine 1 di 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: passo 9, immagine 2 di 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: passo 9, immagine 3 di 3
    • Pull the entire cutting head straight off the shaft holding it in place.

  10. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Bottom Cover: passo 10, immagine 1 di 1
    • Remove the eight Phillips #2 screws on the underside of the cutting head.

  11. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 11, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: passo 11, immagine 2 di 2
    • Remove the bottom cover.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Carsten Frauenheim

Membro da: 03/10/20

110.927 Reputazione

338 Guide realizzate

Team

iFixit Membro di iFixit

Staff

136 Membri

16.573 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 4

Tutti i Tempi: 172