Salta al contenuto principale

Mk Diamond Wet Saws MK660 2010 Blade Replacement

Cosa ti serve

  1. Mk Diamond Wet Saws MK660 2010 Blade Replacement, Blade Cover: passo 1, immagine 1 di 3 Mk Diamond Wet Saws MK660 2010 Blade Replacement, Blade Cover: passo 1, immagine 2 di 3 Mk Diamond Wet Saws MK660 2010 Blade Replacement, Blade Cover: passo 1, immagine 3 di 3
    • Before you begin, make sure to power off and unplug the device from the outlet.

    • If the clear water pump hose is connected, remove it now.

    • Loosen the plastic knob holding the saw's cutting head in place.

    • Lower the cutting head while keeping it steady.

  2. Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 2, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 2, immagine 2 di 2
    • Unscrew the knob.

    • Remove it from the cutting head.

  3. Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 3, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 3, immagine 2 di 2
    • Loosen the plastic knob holding the blade cover in place.

  4. Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 4, immagine 1 di 3 Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 4, immagine 2 di 3 Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 4, immagine 3 di 3
    • Loosen the wing nut on the blade cover pivot shaft.

    • Remove the wing nut and accompanying washer.

  5. Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 5, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 5, immagine 2 di 2
    • Pivot the blade cover up and pull it off the shaft.

  6. Mk Diamond Wet Saws MK660 2010 Blade Replacement, Blade: passo 6, immagine 1 di 3 Mk Diamond Wet Saws MK660 2010 Blade Replacement, Blade: passo 6, immagine 2 di 3 Mk Diamond Wet Saws MK660 2010 Blade Replacement, Blade: passo 6, immagine 3 di 3
    • Insert the provided spanner wrench into one of the four tightening holes on the inner flange behind the blade.

    • Use the the provided nut wrench to loosen the hex nut while providing counterforce with the spanner wrench.

  7. Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 7, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 7, immagine 2 di 2
    • Remove the hex nut.

    • Remove the outer flange.

  8. Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 8, immagine 1 di 2 Mk Diamond Wet Saws MK660 2010 Blade Replacement: passo 8, immagine 2 di 2
    • Remove the cutting blade.

    • The blade can be sharp, so handle with care.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Carsten Frauenheim

Membro da: 03/10/20

110.900 Reputazione

338 Guide realizzate

Team

iFixit Membro di iFixit

Staff

136 Membri

16.567 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 14

Tutti i Tempi: 797