Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Introduzione

This guide will help locate the microphone for removal and/or repair.

Parti

Nessuna parte specificata.

  1. Flip over the Nokia and locate the back cover. Press your thumb on the back cover and slide it off the phone.
    • Flip over the Nokia and locate the back cover. Press your thumb on the back cover and slide it off the phone.

  2. Remove the battery from the phone by hand.
    • Remove the battery from the phone by hand.

  3. There are two tabs located at the top corners of the battery compartment. Use the iFixit opening tool to pry out those tabs. There are two tabs located at the top corners of the battery compartment. Use the iFixit opening tool to pry out those tabs.
    • There are two tabs located at the top corners of the battery compartment. Use the iFixit opening tool to pry out those tabs.

  4. Gently pull off the hinge cap from the top of the phone by hand.
    • Gently pull off the hinge cap from the top of the phone by hand.

  5. Use a T6 Torx Screwdriver to remove the four 7.62mm screws located at the corners of the battery compartment.
    • Use a T6 Torx Screwdriver to remove the four 7.62mm screws located at the corners of the battery compartment.

  6. Open the phone and turn it on its side. You will see a seam around the Nokia’s side. Use the iFixit opening tool to run along this seam to pop the clips holding the casing to the frame.
    • Open the phone and turn it on its side. You will see a seam around the Nokia’s side.

    • Use the iFixit opening tool to run along this seam to pop the clips holding the casing to the frame.

  7. Use your hand to gently pull off the back panel from the bottom half of the phone.
    • Use your hand to gently pull off the back panel from the bottom half of the phone.

  8. Close the phone and place it on a flat surface.
    • Close the phone and place it on a flat surface.

    • Use the plastic opening tool or your finger to lift up the motherboard from the bottom casing.

    • Be careful when pulling up the board; there is still a ribbon cable attached to the back of the board.

  9. Find the underside of the motherboard and locate the ribbon cable that attaches the board to the rest of the phone. Use the plastic opening tool to slowly detach the ribbon cable connector, then pull the motherboard away from the frame.
    • Find the underside of the motherboard and locate the ribbon cable that attaches the board to the rest of the phone. Use the plastic opening tool to slowly detach the ribbon cable connector, then pull the motherboard away from the frame.

  10. Pry the keypad out with the plastic opening tool once the motherboard is moved out of the way.
    • Pry the keypad out with the plastic opening tool once the motherboard is moved out of the way.

  11. Locate the small speaker module on the back of the separated battery compartment. The module is in the lower left hand corner.
    • Locate the small speaker module on the back of the separated battery compartment. The module is in the lower left hand corner.

  12. Use the plastic opening tool to pry out the microphone from the bottom of the compartment.
    • Use the plastic opening tool to pry out the microphone from the bottom of the compartment.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Andrew

Membro da: 04/10/2010

397 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 4-46, Amido Fall 2010 Membro di Cal Poly, Team 4-46, Amido Fall 2010

CPSU-AMIDO-F10S4G46

4 Membri

14 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 265