Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Mad Catz Street Fighter IV FightPad Front Case Replacement

Introduzione

Removing the FightPad's front case for replacing the case or front artwork.

Cosa ti serve

  1. Mad Catz Street Fighter IV FightPad Front Case Replacement, Rear and Side Case: passo 1, immagine 1 di 1

    • Use tweezers to completely remove the sticker from the rear of controller.

    Traduci

  2. Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 2, immagine 1 di 1

    • Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.

    Traduci

  3. Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 3, immagine 1 di 2 Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 3, immagine 2 di 2

    • Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.

    • Use the plastic opening tool to pry the two cases apart.

    Traduci

  4. Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 4, immagine 1 di 2 Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 4, immagine 2 di 2

    • Remove the two rubber side grips.

    Traduci

  6. Mad Catz Street Fighter IV FightPad Front Case Replacement, RS-DP-LS Switch: passo 5, immagine 1 di 2 Mad Catz Street Fighter IV FightPad Front Case Replacement, RS-DP-LS Switch: passo 5, immagine 2 di 2

    • Locate RS-DP-LS switch.

    • Pull upwards on the switch to remove it.

    Traduci

  7. Mad Catz Street Fighter IV FightPad Front Case Replacement, Circuit Board: passo 6, immagine 1 di 1

    • Locate the four 8.3 mm Phillips screws on the circuit board and remove them.

    Traduci

  8. Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 7, immagine 1 di 3 Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 7, immagine 2 di 3 Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 7, immagine 3 di 3

    • Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.

    • Be careful with the wires connected to the circuit board itself as they are thin and delicate.

    • When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.

    Traduci

  9. Mad Catz Street Fighter IV FightPad Front Case Replacement, Buttons: passo 8, immagine 1 di 2 Mad Catz Street Fighter IV FightPad Front Case Replacement, Buttons: passo 8, immagine 2 di 2

    • Remove the six buttons one by one by gripping the back of each one and pushing on them from the front.

    • Use tweezers to remove the rubber part of the directional pad before you try to remove the shoulder buttons.

    • When reinserting the buttons make sure they are in the correct place and oriented correctly.

    Traduci

  10. Mad Catz Street Fighter IV FightPad Front Case Replacement: passo 9, immagine 1 di 1

    • Remove the left and right shoulder buttons by sliding them out of their respective slots.

    Traduci

  11. Mad Catz Street Fighter IV FightPad Front Case Replacement, Front Case: passo 10, immagine 1 di 2 Mad Catz Street Fighter IV FightPad Front Case Replacement, Front Case: passo 10, immagine 2 di 2

    • Pull the plastic piece out from the bottom of the controller.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 5 altri collaboratori

Eric

Membro da: 09/26/12

117 Reputazione

3 Guide realizzate

Distintivi: 10

+7 altri distintivi

Team

Cal Poly, Team 1-7, Propen Fall 2012 Membro di Cal Poly, Team 1-7, Propen Fall 2012

CPSU-PROPEN-F12S1G7

4 Membri

14 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 1,449