Introduzione

This guide is prereq only.

  1. Pull the camera cable connector straight out of its socket on the logic board.
    • Pull the camera cable connector straight out of its socket on the logic board.

    • Pull the cable parallel to the face of the logic board toward the optical drive opening.

    This step did not provide enough direction and is the reason my cable is either broke/not working now. I tried pulling it out of the logic board, as indicated, but it did not budge. I was extremely careful not to damage it, so I gave up on trying to remove it once I saw that it wasn't moving. Lo and behold, once I fired the Macbook up again, the camera is no longer connected. This step should have additional details/explanation as to why the cable may not come out/what to do if it doesn't (I was able to proceed to the next steps by working around the cable, so it didn't even have to be removed as the guide might have you think).

    Does anyone know how to properly fix it/where to buy a replacement camera/iSight cable? I would like to fix this if possible.

    jackalbert - Replica

    I would like to add – several months later, my Macbook Pro failed to turn on and the motherboard had to be replaced. I'm giving partial blame to this guide for failing to adequately describe how to safely proceed on this step (I suspect a bad wifi card was part of the problem). Anyone else following this guide be very wary!

    jackalbert - Replica

  2. Use the flat end of a spudger to carefully pry the AirPort/Bluetooth ribbon cable up off its socket on the logic board.
    • Use the flat end of a spudger to carefully pry the AirPort/Bluetooth ribbon cable up off its socket on the logic board.

    This step literally ruined my MacBook Pro. The ribbon cable pulled off of the logic board, and will no longer reconnect.

    Brian Webb - Replica

  3. Diffondi allegria Fixmas
    Ottieni $12 sul tuo acquisto di $50 o più con il codice FIXMAS12
    Diffondi allegria Fixmas
    Ottieni $12 sul tuo acquisto di $50 o più con il codice FIXMAS12
    • Use the tip of a spudger to pry the four antenna connectors up from their sockets on the AirPort/Bluetooth board.

    I found the problem with my wifi: sadly the connector solder joint j4 of the wifi board was not stable enough. now the socket is inside of the connector and not joined with the board. How do I remove the socket from inside of the connector? Is this even possible?

    Bodo Tasche - Replica

    • De-route all four antenna cables from their channels in the AirPort/Bluetooth housing.

    • De-route the camera cable from its channel in the AirPort/Bluetooth housing.

    Long antenna cable was a little tricky, harder to de-route...slide to narrow part of cable, and then lift out from under the tab

    Christa - Replica

    • Remove the following two screws securing the AirPort/Bluetooth assembly to the upper case:

      • One 8.6 mm Phillips screw

      • One 3.9 mm Phillips screw

    I want to know Lot No. of " 3.9 mm Phillips screw" Step 9.

    That was broken... :( Is there anyone who can help me?

    YoungWook Jo - Replica

    the same problem, do you know which size the screw is??

    adambartusz91 -

    Looking for replacement screws for the Airport/Bluetooth module. The head stripped and I was able to successfully remove the damaged screw but now I need a replacement. If I could get the part number for the screws I could probably order it. It's the screw on the right in step 9.

    MacGyver - Replica

    MacGyver, how did you finally remove that screw? Same problem here.

    Heinz -

    Also curious. Both screws are stripped on mine.

    Marc Opperman -

    Bumping this. I need to know the screw sizes too.

    robbysturms -

    Can i replace a faulty 2011 15" screen with the same one from a 2010 15" model with the same resolution?

    Are they interchangeable?

    lukas - Replica

    It is possible, yes.

    Josh Morelli-Harlan -

    ATTENTION IFIXIT!!

    These two screws strip easily, and we need a guide on how to remove them when they become stripped.

    Please that would be so helpful.

    M Santos - Replica

    • Remove the AirPort/Bluetooth assembly from the upper case, minding any cables that may get caught.

    Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 403