Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three identical Phillips screws from the memory door.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips screws in the battery compartment near the latch.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 6 screws:
-
Two 10 mm T6 Torx screws on either side of the RAM slot.
-
Four 14.5 mm Phillips screws along the hinge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four Phillips screws on the port side of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the computer 90 degrees and remove the two Phillips screws from the rear of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the computer 90 degrees again and remove the four Phillips screws from the side of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case. This stage can be quite tricky. Over the DVD reader are 4 tabs set back which pull out vertically.
-
Note that the two small tongues on the left hand front of the upper case may bend while you remove the upper case. When re-installing, you may need to bend them back to fit in the grooves in the lower case.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
-
Remove the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the display data cable from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up and remove the orange foil shield near the right speaker.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the silver T6 Torx securing the ground loop in the display data cable to the casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the speaker clockwise approximately 30 degrees until it comes free from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the gray and black speaker wires from the top of the logic board, removing tape as necessary.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to flip up the brown plastic flap securing the left ambient light sensor cable to the logic board.
-
Slide the left ambient light sensor cable to the left and out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the left ambient light sensor cable from above the left fan.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the two antenna cables attached to the Airport Extreme card.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single silver Phillips screw located just above the Airport Extreme card.
-
Lift the small silver metal retaining bracket up and out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel back the orange tape on the right side of the Airport Extreme card.
-
Lift the Airport Extreme card up and slide it out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the orange hard drive ribbon cable from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the orange hard drive ribbon from above the ExpressCard cage.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the speaker cable from the front right corner of the left I/O board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 2 screws:
-
One 4.3 mm black T6 Torx screw on the left side of the speaker.
-
One 9.4 mm silver T6 Torx screw on the right side of the speaker.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the left and right speakers out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single silver Phillips screw securing the left ambient light sensor cover to the speaker.
-
Remove the clear plastic ambient light sensor cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to pry the left ambient light sensor board out of its housing on the left speaker.
-
Annulla: non ho completato questa guida.
Altre 4 persone hanno completato questa guida.