Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three identical Phillips screws from the memory door.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips screws in the battery compartment near the latch.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 6 screws:
-
Two 10 mm T6 Torx screws on either side of the RAM slot.
-
Four 14.5 mm Phillips screws along the hinge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four Phillips screws on the port side of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the computer 90 degrees and remove the two Phillips screws from the rear of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the computer 90 degrees again and remove the four Phillips screws from the side of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case. This stage can be quite tricky. Over the DVD reader are 4 tabs set back which pull out vertically.
-
Note that the two small tongues on the left hand front of the upper case may bend while you remove the upper case. When re-installing, you may need to bend them back to fit in the grooves in the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
-
Remove the upper case.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the orange SuperDrive ribbon cable from the logic board, removing tape as necessary.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws:
-
Two 3.3 mm silver Phillips screws on either side of the SuperDrive.
-
One 4.8 mm black Phillips screw at the top right corner of the drive.
-
The 4.8mm screw may be a T6 Torx
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the optical drive up and out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the hard drive and ExpressCard connectors from the left side of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the eight indicated connectors from the logic board, removing tape as necessary.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to flip up the brown plastic flap securing the left ambient light sensor cable to the logic board.
-
Slide the left ambient light sensor cable to the left and out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the silver T6 Torx screw securing the ground loop on the display data cable to the casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single silver T6 Torx screw securing the clear plastic shield over the right ambient light sensor.
-
Lift the clear plastic shield off the right ambient light sensor.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the orange Kapton tape securing the right thermal sensor cable to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 16 screws, moving cables as necessary:
-
One 4.4 mm black Phillips screw to the right of the RAM slot.
-
Nine 4.7 mm silver T6 Torx screws securing the logic board to the lower case.
-
One 6.2 mm black T6 Torx screw on the right side of the left fan.
-
Five 9.4 mm silver T6 Torx screws securing the left and right fans.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Move the display data cable to the right, removing tape as necessary.
-
Peel up and remove the orange foil shield near the right speaker.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the speaker clockwise approximately 30 degrees until it comes free from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the gray and black speaker wires from the top of the logic board, removing tape as necessary.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Peel up the iSight and inverter board cables from above the left fan.
-
Hold the logic board down with one hand and use your other hand to lift the left fan up from its housing. There is a piece of black tape securing the fan to the heat sink. Carefully peel this tape up from the heat sink as you lift the fan up.
-
Place the fan above the Airport card. It is not necessary to entirely remove the fan from the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the right fan up while carefully peeling up the tape which secures the fan to the heat sink.
-
Remove the right fan from the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up the left side of the logic board and disconnect the multi-colored power cable from the bottom of the board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the logic board at the left side and at the thin section, and rotate the logic board out of the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the right thermal sensor cable from the bottom of the logic board near the DVI port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.
-
Pull the chip directly out from its connector.
-
Annulla: non ho completato questa guida.
Altre 53 persone hanno completato questa guida.
4 Commenti
Buying the part, it says that thermal paste is needed for installation. Where?
Thermal paste is needed to transfer heat from the Nvidia GPU and the CPUs to the heat spreader bar which is located below the motherboard. It transfers heat from the CPUs to the fans.
The final part says to just follow the steps in reverse order to reassemble--that isn't quite enough information. It is critical *not* to snug or overtighten the memory door screws from step 2. The screws pass to the bottom of the keyboard, and the keyboard is made of a light material that deforms easily. If you overtighten the screws it will bend the keyboard out of shape and the spacebar will not work properly.
After installing the screws on the memory door, then test that the space bar goes down and back up properly. If it doesn't back the screws out and try again. Do not proceed with the rest of reassembly if the keyboard is not working.
I totally second this!