Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Premere con le dita entrambe le linguette di sgancio della batteria verso l'esterno e sollevare la batteria dal computer.
-
-
-
Rimuovere le tre viti con testa a croce da 2 mm dallo sportello della memoria.
-
Sollevare lo sportello della memoria affinché sia possibile prenderlo e farlo scorrere verso di sé, estraendolo dall'alloggiamento.
-
-
-
Rimuovere le due viti con testa a croce da 2,8 mm nello scomparto della batteria in prossimità della chiusura.
-
-
-
Sollevare il case dalla parte posteriore e, mediante le dita, liberarlo progressivamente dai lati. Dopo aver liberato i fianchi, potrebbe essere necessario inclinare il case verso l'alto e verso il basso per liberare la parte anteriore del case superiore.
-
Sono presenti quattro levette di plastica sopra lo slot del DVD e in alto e a sinistra del sensore infrarossi. Queste levette potrebbero essere difficili da sganciare senza fare leva. Inoltre, potrebbe essere difficile riagganciarle durante il riassemblaggio.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the iSight cable from the logic board by sliding the cable to the left and out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the left fan and left ambient light sensor cables by placing a spudger beneath each cable and lifting up.
-
Peel up the left ambient light sensor cable from above the left fan, removing tape as necessary.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 3 screws:
-
One 6.2 mm black T6 Torx screw from the right side of the fan.
-
Two 9.4 mm silver T6 Torx screws from the left side of the fan.
-
Lift the fan up; carefully peel up the tape that secures the fan to the heat sink as you go.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the hard drive and ExpressCard connectors from the left side of the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the two antenna cables attached to the Airport Extreme card.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single black 4mm T6 Torx screw located just above the Airport Extreme card.
-
Remove the metal bracket that was securing the Airport Extreme card.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the Airport Extreme card up and slide it out of its connector.
-
Deroute the Airport antenna cables from their channel in the left speaker.
-
Peel up the orange hard drive cable from above the ExpressCard cage.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the speaker cable from the corner of the left I/O board.
-
Lift the left speaker assembly out of its housing and place it in the area previously occupied by the left fan.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the large gray and black power cable from the left I/O board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to disconnect the inverter cable from the corner of the left I/O board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 5 screws/standoffs:
-
Four black 4 mm T6 Torx screws securing the left I/O board to the lower case.
-
One 4 mm standoff located between the audio jacks.
-
Lift up the right side of the left I/O board and slide it out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following four screws:
-
One 3.1 mm at upper right.
-
One 4.9 mm at upper left.
-
Two 2.2 mm along the bottom.
-
Lift the left I/O board off the ExpressCard cage.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the short left I/O board cable.
-
Left I/O board remains.
-
Annulla: non ho completato questa guida.
Altre 52 persone hanno completato questa guida.
Un commento
Just successfully completed this repair. The guide is absolutely spot on with very clear high resolution pictures. I was working very carefully through each step and had no issues at all throughout the process until the very end when I couldn't find the last screw for the ram cover. Luckily it was stuck to the magnetic MagSafe charger port on the side of the I/O board!
I personally would rate this as a moderate repair instead of a difficult one as there is no specialist skills required like soldering. Thanks again!