Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three identical Phillips screws from the memory door.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following 6 screws:
-
Two 10 mm T6 Torx screws on either side of the RAM slot.
-
Four 14.5 mm Phillips screws along the hinge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four 3.2 mm Phillips screws on the port side of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case (there are some hidden plastic clips that need to be clicked off).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
-
Remove the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the three antenna cables attached to the Airport Extreme card.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Deroute the Airport antenna cables from their channel in the left speaker.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the iSight cable from the logic board by sliding the cable to the left and out of its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the inverter cable from the logic board by placing a spudger beneath the cable and lifting up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the display data cable from the logic board by pulling sideways.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the silver T6 Torx securing the ground loop in the display data cable to the casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Support the display with one hand while removing the following 3 screws:
-
Two 9.5 mm silver T6 Torx screws with threads on only part of the shaft on the inside of the display hinges.
-
One 9.5 mm silver T6 Torx screw with threads on the entire shaft on the outside of the left hinge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the display assembly on both sides and lift it up and out of the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 5 mm Phillips screws from the lower left and right corners of the display (two screws total).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the flat end of a spudger perpendicular to the face of the display between the plastic strip attached to the rear bezel and the front bezel.
-
With the spudger still inserted, rotate it away from the display to separate the front and rear bezels.
-
Work along the left edge of the display until the rear bezel is evenly separated from the front bezel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the flat end of a spudger perpendicular to the face of the display between the plastic strip attached to the rear bezel and the front bezel.
-
With the spudger still inserted, rotate it away from the display to separate the front and rear bezels.
-
Work along the right edge of the display until the rear bezel is evenly separated from the front bezel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the flat end of a spudger between the front bezel and the plastic strip attached to the rear bezel near the screw holes at the bottom corners of the display.
-
Rotate your spudger toward the rear bezel to separate it from the front bezel.
-
If necessary, enlarge the gap between the lower edge of the rear bezel and the clutch cover until the two components are completely separated.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the rear bezel by its bottom edge and rotate it away from the display assembly to separate the top edge.
-
Remove the rear display bezel from the display assembly.
-
Annulla: non ho completato questa guida.
Altre 5 persone hanno completato questa guida.