Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Sostituzione Inverter del MacBook Core 2 Duo

Cosa ti serve

  1. Sostituzione Inverter del MacBook Core 2 Duo, Batteria: passo 1, immagine 1 di 1
    • Usa una monetina o uno spudger per ruotare la vite di blocco della batteria di 90 gradi in senso orario.

  2. Sostituzione Inverter del MacBook Core 2 Duo: passo 2, immagine 1 di 1
    • Estrai la batteria dal computer.

  3. Sostituzione Inverter del MacBook Core 2 Duo, Installazione del coperchio della memoria nel MacBook Core 2 Duo: passo 3, immagine 1 di 1
    • Svitare le tre viti con testa a croce equidistanti lungo la parete posteriore dello scomparto della batteria.

    • Le viti resteranno dentro il coperchio metallico della memoria, pertanto non si rischia di perderle.

  4. Sostituzione Inverter del MacBook Core 2 Duo: passo 4, immagine 1 di 1
    • Ruotare il coperchio della memoria a forma di L affinché liberi l'apertura dello scomparto della batteria e rimuoverlo dal computer.

  5. Sostituzione Inverter del MacBook Core 2 Duo, Case Superiore: passo 5, immagine 1 di 1
    • Rimuovere le 3 viti seguenti:

    • Una vite con testa a croce n. 00 da 11 mm nella parte centrale del case. (Testa: 5 mm di diametro x 0,75 mm di spessore)

    • Due viti con testa a croce n. 00 da 14,5 mm (testa: 5 mm di diametro x 0,75 mm di spessore)

    • Se le viti restano incastrate nel case, è possibile utilizzare un cacciavite magnetico per recuperarle.

    • La vite più corta delle tre va al centro.

  6. Sostituzione Inverter del MacBook Core 2 Duo: passo 6, immagine 1 di 1
    • Presta particolare attenzione a queste viti, si rompono facilmente!

    • Rimuovi le 3 viti seguenti dalla parete posteriore dello scomparto della batteria:

    • Una vite con testa a croce Phillips #0 da 3 mm (testa: 2,75 mm di diametro).

    • Due viti con testa a croce Phillips #0 da 4 mm su entrambi i lati. (Testa: 2,75 mm di diametro)

  7. Sostituzione Inverter del MacBook Core 2 Duo: passo 7, immagine 1 di 1
    • Rimuovere le due viti con testa a croce da entrambi i lati della parete destra dello scomparto della batteria (non quelle più vicine al connettore della batteria).

    • Due viti con testa a croce n. 000 da 6,25 mm. (Testa: 4 mm di diametro x 0,5 mm di spessore)

  8. Sostituzione Inverter del MacBook Core 2 Duo: passo 8, immagine 1 di 1
    • Rimuovere le quattro viti con testa a croce indicate dalla parete anteriore dello scomparto della batteria. Operando da sinistra, rimuovere la seconda, la quarta, la settima e la nona vite.

    • Quattro viti con testa a croce n. 000 da 3,25 mm. (Testa: 4 mm di diametro x 4 mm di spessore)

  9. Sostituzione Inverter del MacBook Core 2 Duo: passo 9, immagine 1 di 1
    • Rimuovere le 4 viti seguenti dalla parte posteriore del computer:

    • La vite più lunga va nella parte interna, mentre quelle più corte nella parte esterna.

    • Due viti con testa a croce n. 00 da 11 mm con gambo (2,2 mm di diametro x 2 mm di lunghezza) (Testa: 3,2 mm di diametro x 0,5 mm di spessore)

    • Due viti con testa a croce n. 00 da 7,25 mm con gambo (2mm di diametro x 3,75 mm di lunghezza) (Testa: 3,2 mm di diametro x 0,5 mm di spessore)

  10. Sostituzione Inverter del MacBook Core 2 Duo: passo 10, immagine 1 di 1
    • Rimuovere le due viti con testa a croce dal lato con unità ottica del computer.

    • Due viti con testa a croce n. 00 da 5,2 mm con gambo (2,3mm di diametro x 3,5 mm di lunghezza) (Testa: 3,2 mm di diametro x 0,5 mm di spessore)

    • Non è necessario rimuovere le viti analoghe sull'altro lato del computer.

  11. Sostituzione Inverter del MacBook Core 2 Duo: passo 11, immagine 1 di 1
    • È presente un cavo piatto del trackpad e della tastiera che collega il case superiore alla scheda logica, pertanto non rimuovere completamente il case superiore.

    • A partire dalle vicinanze del display e lavorando attorno alla parte anteriore del computer, aprire il case superiore. Per eseguire l'operazione, può essere utile adoperare un plettro per chitarra medio o di tipo A.

    • È probabile che il case superiore sia bloccato presso la connessione sopra l'unità ottica. In questo caso, liberare prima tutti gli altri lati, quindi procedere a tirare verso l'alto il case superiore da entrambi i lati dell'apertura dell'unità ottica.

    • Se metti in piedi la base per vederci meglio potresti far cadere un totale di quattro clip di plastica grigia che tengono in posizione la tastiera. Niente panico. Sono alloggiate in apposite fessure nell'angolo superiore destro, vicino al lettore CD.

  12. Sostituzione Inverter del MacBook Core 2 Duo: passo 12, immagine 1 di 3 Sostituzione Inverter del MacBook Core 2 Duo: passo 12, immagine 2 di 3 Sostituzione Inverter del MacBook Core 2 Duo: passo 12, immagine 3 di 3
    • Tenendo il case superiore sollevato, estrarre la linguetta nera del cavo argentato dal relativo connettore.

    • Se la linguetta nera non è presente, si può usare uno spudger per rimuovere delicatamente il connettore dall'alloggiamento. Il connettore è alto, quindi fai attenzione a tirarlo in verticale.

    • Nel caso di rottura del cavo del case superiore durante la rimozione, è possibile acquistarlo separatamente e consultare questa guida che ne semplifica la soluzione.

    • Con il case superiore rimosso, puoi sfruttare la possibilità di rimuovere polvere, peli, ecc. La cosa migliore è usare una bomboletta di aria compressa; se usi un pennello assicurati che sia realizzato in un materiale (di solito pelo animale) che non genera elettricità statica, potenzialmente distruttiva per l'elettronica.

    • Al momento del riassemblaggio, sono presenti quattro levette in plastica grigia sul lato della tastiera in corrispondenza all'unità ottica (vedi la seconda immagine). Queste devono essere installate nelle rispettive fessure, affinché la tastiera si agganci correttamente.

    • Per semplificare la procedura di rimontaggio, è meglio tirare fuori le clip per prime sollevando il tutto delicatamente. Stai attento a non metterci troppa forza per evitare rotture.

  13. Sostituzione Inverter del MacBook Core 2 Duo, Unità Ottica: passo 13, immagine 1 di 1
    • Prendere la linguetta in plastica bianca collegata al disco rigido e tirarla verso sinistra, rimuovendo il disco dal computer.

  14. Sostituzione Inverter del MacBook Core 2 Duo: passo 14, immagine 1 di 1
    • Rimuovere le due viti con testa a croce dal bordo anteriore dell'unità ottica.

    • Due viti con testa a croce n. 000 da 3,25 mm, (testa: 4 mm di diametro x 0,3 mm di spessore)

  15. Sostituzione Inverter del MacBook Core 2 Duo: passo 15, immagine 1 di 1
    • Scollegare il cavo piatto arancione dell'unità ottica dalla scheda logica. È possibile scollegare il cavo anche estraendolo mediante un inseritore.

  16. Sostituzione Inverter del MacBook Core 2 Duo: passo 16, immagine 1 di 1
    • Scollegare il cavo dati del display appena esposto. Se non sono presenti linguette da tirare nella parte superiore del connettore, potrebbe essere utile adoperare un inseritore per scollegare il connettore.

  17. Sostituzione Inverter del MacBook Core 2 Duo: passo 17, immagine 1 di 1
    • Scollegare il cavo del disco rigido ancora una volta esposto.

  18. Sostituzione Inverter del MacBook Core 2 Duo: passo 18, immagine 1 di 1
    • Stacca il nastro alluminato tra la ventola e il disco ottico. Solleva il nastro dal lato della ventola, lasciandolo attaccato al disco ottico.

    • In fase di rimontaggio, assicurati di allineare i cavi sotto il nastro prima di riattaccarlo.

  19. Sostituzione Inverter del MacBook Core 2 Duo: passo 19, immagine 1 di 1
    • Estrarre il cavo dati del display da lungo il bordo dell'unità ottica per rendere accessibile una vite con testa a croce argentata.

  20. Sostituzione Inverter del MacBook Core 2 Duo: passo 20, immagine 1 di 1
    • Rimuovere la vite con testa a croce da 2 mm che fissa l'unità ottica.

    • Il cavo Bluetooth potrebbe coprire la vite, pertanto spostarlo di lato con attenzione prima di iniziare a svitare.

  21. Sostituzione Inverter del MacBook Core 2 Duo: passo 21, immagine 1 di 1
    • Sollevare la scheda dell'antenna Bluetooth dal lato destro dell'unità ottica.

  22. Sostituzione Inverter del MacBook Core 2 Duo: passo 22, immagine 1 di 1
    • Rimuovere il cavo del disco rigido da lungo la parte anteriore dell'unità ottica.

  23. Sostituzione Inverter del MacBook Core 2 Duo: passo 23, immagine 1 di 1
    • Sollevare il bordo anteriore dell'unità ottica e farla scorrere verso l'alto e fuori dal computer.

  24. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 24, immagine 1 di 1
    • For original Macbook Core Duo and Core 2 Duo models, remove these 3 screws:

    • Two 3 mm Phillips near the right speaker.

    • One 6 mm Phillips threaded through a hole in a plastic finger above the subwoofer.

    • When reinstalling the screw above the subwoofer, be careful not to over-tighten it or the subwoofer's plastic could crack.

    • For Santa Rosa/Penryn and 2009 models, which don't have a c-channel:

    • Remove only the single 3 mm Phillips screw from the right speaker, and skip step 26.

  25. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 25, immagine 1 di 1
    • Lift the right speaker out of its housing and set it to the side.

  26. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 26, immagine 1 di 1
    • If you have a Santa Rosa/Penryn or 2009 model, skip this step.

    • Using a spudger, gently pry up the white plastic slot and slide the metal c-channel to the right and away from the display.

  27. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 27, immagine 1 di 1
    • Use a spudger to carefully disconnect the microphone cable from the logic board. You'll want to work from side to side, and slowly wiggle the plug back and out of its socket.

    • Pulling on this plug vertically will break its socket off the logic board. This connector is removed only horizontally by gently pulling the microphone cable toward the screen while working a spudger between the connector and the socket.

  28. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 28, immagine 1 di 1
    • Lift up on the black right speaker cable with one hand, and deroute the microphone cable from the silver metal clip just above the right RAM slot.

    • This metal clip may not be present in all models. Be sure that the cable is free from any hold downs around this area before proceeding.

  29. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 29, immagine 1 di 1
    • If you didn't remove the ground lug retaining screw in step 20 above, remove it now. It's a 7mm (may be 4mm or 3mm in Santa Rosa/Penryn and 2009 models) Phillips screw securing the ground lugs on the right speaker cable and microphone cable to the metal frame.

  30. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 30, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 30, immagine 2 di 2
    • Deroute the microphone cable and the black display data cable from the tabs at the bottom of the subwoofer.

    • During reassembly, while there may seem to be more than one way to route the cables, the best way is as shown in photo 2. Click on the photo for a larger view.

  31. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 31, immagine 1 di 1
    • Remove the single 3 mm Phillips screw securing the ground lug in the display data cable located just above the Bluetooth board. This screw may also be securing a ground lug in the speaker cable.

  32. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 32, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 32, immagine 2 di 2
    • Disconnect the antenna cables from the Airport card:

    • If you have an original MacBook Core Duo or Core 2 Duo model, see the first picture, which shows that there are three antenna cables.

    • If you have a MacBook Core 2 Duo Santa Rosa/Penryn or 2009 model, there are only two antenna cables, and the plug/socket for the black inverter cable is in a different location. There may be a square foam piece over the plug/socket for the inverter board connector.

    • Disconnect the inverter cable from its socket by inserting a spudger between the right or left ends of the plug and the socket, and prying gently vertically. Do NOT pry up on the socket--you must pull up on the plug alone, vertically out of the socket. Do not pull in the direction of the cable wires or you will tear the socket off the logic board.

  33. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 33, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 33, immagine 2 di 2
    • For original Macbook Core Duo and Core 2 Duo models, see first picture and remove the following 2 screws from the right hinge mount:

    • One 6 mm Phillips on the left side of the hinge mount.

    • One 10 mm Phillips on the right side of the hinge mount.

    • For Santa Rosa/Penryn and 2009 models, see second picture and remove the following 3 screws from the right hinge mount:

    • One 3 mm smalller diameter Phillips on the far left.

    • One 5.2 mm larger diameter, 4.2 mm head Phillips in the middle.

    • One 10 mm larger diameter, 4.2mm head Phillips from the far right.

    • Before removing the right hinge mount, take care to see how its pieces fit together, including the small white plastic piece. Knowing how the mount pieces fit together will help with reassembly. Lift the right hinge mount with the small white plastic piece out of the computer.

  34. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 34, immagine 1 di 1
    • Hold the display with one hand while removing the following 3 screws from the left hinge mount:

    • One 7.2 mm smaller diameter Phillips from the right side.

    • One 5.2 mm larger diameter Phillips from the middle.

    • One larger diameter 10 mm Phillips from the left side.

    • Before removing the left hinge mount, take care to see how its pieces fit together, including the small white plastic piece. Knowing how the mount pieces fit together will help with reassembly.

    • In 2009 models, the shape of the left hinge mount may be different than shown in the photo, but the locations and sizes of its screws are the same.

    • Lift the left hinge mount with white plastic piece out of the computer.

    • Check that the cables coming out of the right end of the left hinge are not trapped under other cables.

  35. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 35, immagine 1 di 1
    • Grasp the display assembly on either side and lift it up and out of the computer, taking care that the cables attached to the display don't snag on parts in the lower case.

  36. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 36, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    Plastic Cards
    $2.99
    Compra
    • The following steps should be identical for both white and black MacBooks.

    • Use a thin plastic card to release the tabs and their clips holding the front display bezel to the display assembly. There are five tabs along the left side of the display bezel.

    • You may find some display bezels are easier to remove if you work from their inside edges, directly adjacent to/above the LCD panel.

    • Don't use a card that cannot be replaced if damaged. The clips can be difficult to remove and the card can bend and break, rendering it useless.

  37. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 37, immagine 1 di 1
    • Continue to free the tabs along the the top edge of the display assembly.

    • Be careful when working near the iSight camera.

  38. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 38, immagine 1 di 1
    • Next, free the five tabs securing the display bezel on the right side.

  39. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 39, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 39, immagine 2 di 2
    • Lift up the front display bezel from the top and use your plastic card to free the tabs along the bottom edge of the display bezel.

    • Make sure that your card is between the metal frame around the LCD panel and the display bezel and not touching the LCD panel itself.

    • After freeing all holding tabs, lift the front display bezel away from the display assembly.

    • When reinstalling the front display bezel onto the display housing, you may find it easier to get the tabs and clips to connect if you push on the four sides of the bezel in this order: top, bottom, then the sides (left or right). You may have to apply extra pressure along the bottom side of the bezel to get it to snap into place firmly.

  40. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 40, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 40, immagine 2 di 2
    • Sometimes when removing the front display bezel, the retaining clips that should remain captive in the LCD brackets come out with the front display bezel. Follow this and the next step to transfer the clips back to the LCD bracket.

    • Use a metal spudger or another thin tool to carefully pry the gray plastic clips off the tabs molded into the front display bezel. A 0.8mm flat screwdriver may be useful for this step. You may find that it's easier to remove some of these clips by prying up on their long sides.

    • Be careful, as the clips are made of thin plastic and are inherently delicate.

  41. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 41, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 41, immagine 2 di 2
    • Insert one end of the retaining clip beneath the edge of its recess cut into the LCD bracket.

    • Use the edge of a spudger to push the short hook tab on the underside of the other end of the retaining clip into the recess cut into the LCD bracket.

    • The second picture shows a retaining clip properly installed.

    • You may find it easier to get the short hook tabs on the underside of each end of the clip to fit down inside their cutout in the LCD bracket by first very slightly bending down the two ends of the clip, but be careful not to bend the clips too much--only a slight bend is needed, and too much force will break them.

  42. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 42, immagine 1 di 1
    • Remove the three 4.2 mm Phillips screws securing the clutch cover.

  43. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 43, immagine 1 di 1
    • While holding the display down with one hand, use your other hand to lift the left end of the clutch cover off the clutch hinge and guide the inverter cable and AirPort cables through the gap in the clutch cover. If the cables snag on the two hooked tabs on the inside end of the clutch cover, free them carefully.

    • It may help to wiggle the clutch cover as you pull it up from the display.

    • During reassembly, make sure not to pinch the black inverter cable or the Airport wires when snapping the left end of the clutch cover back into place. To avoid pinching, it may help to lift up and hold these cables and wires in place at the top of the hinge, rather than leaving them running along the sides of the hinge.

  44. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 44, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 44, immagine 2 di 2
    • Lift up the right end of the clutch cover while guiding the display data and iSight cables through the gap and the two hooked tabs at the right end of the clutch cover. If the cables snag on the two hooked tabs, free them carefully.

    • Lift the clutch cover off of the display assembly.

    • During reassembly, avoid pinching the display data and iSight cables. While guiding the right end of the clutch cover into place, but before snapping it down, guide these cables between the two hooked tabs inside the right end of the clutch cover, and up into the curved area of the clutch cover, above the hinge.

    • Also avoid pinching the backlight wires (with the white connector on the end, plugged into the right end of the inverter). They should run under the upper right edge of the clutch cover. In some models, the two wires are gray and black, and in others they're white and pink. They lead into a hole in the lower right edge of the LCD to the backlight.

  45. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 45, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 45, immagine 2 di 2
    • Slightly lift the newly-revealed inverter board out of its housing and disconnect the black inverter cable from the left end of the board.

  46. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 46, immagine 1 di 2 Sostituzione Inverter del MacBook Core 2 Duo: passo 46, immagine 2 di 2
    • Disconnect the white inverter cable from the right end of the inverter board.

  47. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Sostituzione Inverter del MacBook Core 2 Duo: passo 47, immagine 1 di 1
    • Remove the inverter board from the display.

Conclusione

Per riassemblare il tuo dispositivo, segui i passi descritti in ordine inverso.

Altre 151 persone hanno completato questa guida.

Un ringraziamento speciale a questi traduttori:

en it

100%

Questi traduttori ci stanno aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›

8 Commenti

Awesome site and awesome guide. This exteneded the life of my MacBook. I can't thank you enough!!!!

stuartjwaldner - Replica

For about 3 years I had been dealing with my screen backlight shuting off. I would then dim the screen up and down until I could get it to stay. Sometimes it would work the first time other times I would be doing it for 10 minutes and other times I would give up for a few hours and come back and the screen would be on again. It would also do this sometimes when I opened the laptop at a certain angle or bumped the computer.

Well after these years very annoying behavior, my screen wont turn back on. I can see my desktop when I shine a light on the screen and hear the fan running so I know the computer works fine.

I've tried unpluging the inverter board to see if it was a loose connection, but that didn't work. I tried wiggling it around until the screen turned on and nothing.... Please help!

Is this a problem with my inverter or the inverter cable? Or the backlight cable?

What parts should I buy?

4321ora - Replica

Hi, I've had the same trouble. Today I solved with a spray electronic cleaner :)

19fra71 -

Hi everybody! Last year bought a new inverter, new cable and other stuff and replaced. Problem not solved, screen still turning black. Thinking to get a new display, but today bought spray electronic cleaner, sprayed over the display data cable (https://d3nevzfk7ii3be.cloudfront.net/ig...). Problem &&^&^$^ solved! :) Time: 15 mins, money: 5$. Good tutorial tho! :P

19fra71 - Replica

These are a very comprehensive set of instructions and give a really good grand tour of the innards of a MacBook 8. They are also useful for replacing the hard drive or the optical drive.

Couple of hints:

1. Have on hand some canned compressed air - the inside of a laptop is generally quite full of dust and fluff.

2. Also have on hand some contact cleaner spray (do NOT use degreasers/lubricants/anti rust sprays such as RP 7 or WD 50). Contact cleaner sprays generally only contact isopropyl alchohol. It's good to give exposed contacts a bit of a clean - even grease from fingertips can affect conductivity and hence performance. (If possible, use powder free surgical gloves).

3. Make sure you have the right tools (don't skimp - buy the tools set from iFixit). Not using the right spudger on a plug could be the cause of irreparable damage to the circuit board.

(continued next posting)

brightvt - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 7

Ultimi 30 Giorni: 45

Tutti i Tempi: 110,035