Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Usa una monetina o uno spudger per ruotare la vite di blocco della batteria di 90 gradi in senso orario.
-
-
-
Svita le tre viti con testa a croce equidistanti lungo la parete posteriore dello scomparto della batteria.
-
-
-
Rimuovere le 3 viti seguenti:
-
Una vite con testa a croce n. 00 da 11 mm nella parte centrale del case. (Testa: 5 mm di diametro x 0,75 mm di spessore)
-
Due viti con testa a croce n. 00 da 14,5 mm (testa: 5 mm di diametro x 0,75 mm di spessore)
-
-
-
Rimuovere le quattro viti con testa a croce indicate dalla parete anteriore dello scomparto della batteria. Operando da sinistra, rimuovere la seconda, la quarta, la settima e la nona vite.
-
Quattro viti con testa a croce n. 000 da 3,25 mm. (Testa: 4 mm di diametro x 4 mm di spessore)
-
-
-
Rimuovere le 4 viti seguenti dalla parte posteriore del computer:
-
La vite piรน lunga va nella parte interna, mentre quelle piรน corte nella parte esterna.
-
Due viti con testa a croce n. 00 da 11 mm con gambo (2,2 mm di diametro x 2 mm di lunghezza) (Testa: 3,2 mm di diametro x 0,5 mm di spessore)
-
Due viti con testa a croce n. 00 da 7,25 mm con gambo (2mm di diametro x 3,75 mm di lunghezza) (Testa: 3,2 mm di diametro x 0,5 mm di spessore)
-
-
-
Tenendo il case superiore sollevato, estrarre la linguetta nera del cavo argentato dal relativo connettore.
-
Con il case superiore rimosso, puoi sfruttare la possibilitร di rimuovere polvere, peli, ecc. La cosa migliore รจ usare una bomboletta di aria compressa; se usi un pennello assicurati che sia realizzato in un materiale (di solito pelo animale) che non genera elettricitร statica, potenzialmente distruttiva per l'elettronica.
-
-
-
Prendere la linguetta in plastica bianca collegata al disco rigido e tirarla verso sinistra, rimuovendo il disco dal computer.
-
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
For original Macbook Core Duo and Core 2 Duo models, remove these 3 screws:
-
Two 3 mm Phillips near the right speaker.
-
One 6 mm Phillips threaded through a hole in a plastic finger above the subwoofer.
-
For Santa Rosa/Penryn and 2009 models, which don't have a c-channel:
-
Remove only the single 3 mm Phillips screw from the right speaker, and skip step 26.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Lift the right speaker out of its housing and set it to the side.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Using a spudger, gently pry up the white plastic slot and slide the metal c-channel to the right and away from the display.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use a spudger to carefully disconnect the microphone cable from the logic board. You'll want to work from side to side, and slowly wiggle the plug back and out of its socket.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Lift up on the black right speaker cable with one hand, and deroute the microphone cable from the silver metal clip just above the right RAM slot.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
If you didn't remove the ground lug retaining screw in step 20 above, remove it now. It's a 7mm (may be 4mm or 3mm in Santa Rosa/Penryn and 2009 models) Phillips screw securing the ground lugs on the right speaker cable and microphone cable to the metal frame.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Deroute the microphone cable and the black display data cable from the tabs at the bottom of the subwoofer.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the single 3 mm Phillips screw securing the ground lug in the display data cable located just above the Bluetooth board. This screw may also be securing a ground lug in the speaker cable.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Disconnect the antenna cables from the Airport card:
-
If you have an original MacBook Core Duo or Core 2 Duo model, see the first picture, which shows that there are three antenna cables.
-
If you have a MacBook Core 2 Duo Santa Rosa/Penryn or 2009 model, there are only two antenna cables, and the plug/socket for the black inverter cable is in a different location. There may be a square foam piece over the plug/socket for the inverter board connector.
-
Disconnect the inverter cable from its socket by inserting a spudger between the right or left ends of the plug and the socket, and prying gently vertically. Do NOT pry up on the socket--you must pull up on the plug alone, vertically out of the socket. Do not pull in the direction of the cable wires or you will tear the socket off the logic board.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
For original Macbook Core Duo and Core 2 Duo models, see first picture and remove the following 2 screws from the right hinge mount:
-
One 6 mm Phillips on the left side of the hinge mount.
-
One 10 mm Phillips on the right side of the hinge mount.
-
For Santa Rosa/Penryn and 2009 models, see second picture and remove the following 3 screws from the right hinge mount:
-
One 3 mm smalller diameter Phillips on the far left.
-
One 5.2 mm larger diameter, 4.2 mm head Phillips in the middle.
-
One 10 mm larger diameter, 4.2mm head Phillips from the far right.
-
Before removing the right hinge mount, take care to see how its pieces fit together, including the small white plastic piece. Knowing how the mount pieces fit together will help with reassembly. Lift the right hinge mount with the small white plastic piece out of the computer.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Hold the display with one hand while removing the following 3 screws from the left hinge mount:
-
One 7.2 mm smaller diameter Phillips from the right side.
-
One 5.2 mm larger diameter Phillips from the middle.
-
One larger diameter 10 mm Phillips from the left side.
-
Lift the left hinge mount with white plastic piece out of the computer.
-
Check that the cables coming out of the right end of the left hinge are not trapped under other cables.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Grasp the display assembly on either side and lift it up and out of the computer, taking care that the cables attached to the display don't snag on parts in the lower case.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
Attrezzo utilizzato in questo passaggio:Plastic Cards$2.99-
Use a thin plastic card to release the tabs and their clips holding the front display bezel to the display assembly. There are five tabs along the left side of the display bezel.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Continue to free the tabs along the the top edge of the display assembly.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Next, free the five tabs securing the display bezel on the right side.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Lift up the front display bezel from the top and use your plastic card to free the tabs along the bottom edge of the display bezel.
-
After freeing all holding tabs, lift the front display bezel away from the display assembly.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Use a metal spudger or another thin tool to carefully pry the gray plastic clips off the tabs molded into the front display bezel. A 0.8mm flat screwdriver may be useful for this step. You may find that it's easier to remove some of these clips by prying up on their long sides.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Insert one end of the retaining clip beneath the edge of its recess cut into the LCD bracket.
-
Use the edge of a spudger to push the short hook tab on the underside of the other end of the retaining clip into the recess cut into the LCD bracket.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the three 4.2 mm Phillips screws securing the clutch cover.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
While holding the display down with one hand, use your other hand to lift the left end of the clutch cover off the clutch hinge and guide the inverter cable and AirPort cables through the gap in the clutch cover. If the cables snag on the two hooked tabs on the inside end of the clutch cover, free them carefully.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Lift up the right end of the clutch cover while guiding the display data and iSight cables through the gap and the two hooked tabs at the right end of the clutch cover. If the cables snag on the two hooked tabs, free them carefully.
-
Lift the clutch cover off of the display assembly.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Lift the inverter slightly out of the display.
-
Disconnect the inverter cable from the left side of the inverter board.
-
Set the inverter board back down into its recess molded into the rear display bezel.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Gently peel back the strip of tape covering the inverter cable.
-
Remove the single 3.2 mm Phillips screw securing the inverter cable to the left clutch hinge.
-
-
Questo passaggio รจ privo di traduzione. Aiuta a tradurlo
-
Remove the inverter cable from the display.
-
Annulla: non ho completato questa guida.
Altre 249 persone hanno completato questa guida.
32 Commenti
i did it! Was quite scary opening and putting those parts together. But screen good as new now! :D :D :D
This fix took me 5 hours to do from start to finish. Most difficult part was removing the keyboard assm on the front left corner. It gets caught under the metal support brace inside the case where the two outside screws are. Very tedious job but worth it because it fixed the backlight problem on my Penyrn Macbook.