Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a P5 driver to remove the following screws:
-
Two 7.6 mm screws (with a 2.7mm collar)
-
Two 7.1 mm screws
-
Six 2.3 mm screws
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
-
Remove the lower case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the plastic shield covering the battery PCB.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a T3 torx driver to remove two 2.3mm screws from the battery PCB:
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a spudger to slide the battery connector parallel to the logic board and out of its socket on the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a T3 Torx driver to remove the one 1.1 mm screw securing the antenna cable bracket.
-
Remove the antenna cable bracket.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the point of a spudger under one of the antenna cables close to the connector.
-
Pry straight up to disconnect the cable.
-
Repeat for the other antenna cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a T3 Torx driver to remove the two 1.3 mm screws securing the display cable connector bracket.
-
Remove the display cable connector bracket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry up the display cable connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a T3 Torx driver to remove the two 1.1 mm screws securing the flex cable brackets.
-
Remove the two brackets.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a T5 Torx driver to remove the following screws:
-
Four 7.1 mm screws
-
Two 4.2 mm (Black) screws
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the antenna bar straight up and out of the case. Take care not to snag the antenna bar on any cables or connectors.
-
Remove the antenna bar.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a T9 Torx driver to remove the six 4.7 mm screws securing the display hinges to the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With the MacBook still screen-side down, carefully lift the upper case to open the MacBook as far as possible.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully rotate the upper case to a 90 degree angle with the display.
-
Keeping the display flat, tilt the upper approx 5-10 degrees to the left. Move the upper case to the right, the hinges should easily slide out of the upper case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Display should now be separate from the upper case.
-
Annulla: non ho completato questa guida.
Altre 2 persone hanno completato questa guida.
2 Commenti
Great guide! Did you encounter any tamper-proof seals? Anything that would make it obvious that the MacBook was disassembled?
No tamper proof seals encountered. Didn’t find anything that would “make it obvious that the MacBook was disassembled”.