Salta al contenuto principale
  1. Prima di cominciare, chiudi il tuo portatile e appoggialo a testa in giù su una superfice morbida.
    • Prima di cominciare, chiudi il tuo portatile e appoggialo a testa in giù su una superfice morbida.

    • Svita le seguenti dieci viti:

    • Due viti pentalobe da 8 mm

    • Otto viti pentalobe da 2,5 mm

    • Il cacciavite speciale richiesto per svitare le viti Pentalobe può essere trovato qui.

  2. Infila le dita tra lo schermo e il case inferiore e tira verso l'alto per sganciare la cover dal MacBook Air.
    • Infila le dita tra lo schermo e il case inferiore e tira verso l'alto per sganciare la cover dal MacBook Air.

    • Rimuovi la cover inferiore e mettila da parte.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    In this step you will disconnect the battery to help avoid shorting out any components during service. Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
    • In this step you will disconnect the battery to help avoid shorting out any components during service.

    • Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

    • Bend the battery cable slightly away from the logic board so the connector will not accidentally contact its socket.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.
    • Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use a spudger to help lift the free end of the SSD just enough to grab it with your other hand. Do not lift the end of the SSD excessively.
    • Use a spudger to help lift the free end of the SSD just enough to grab it with your other hand.

    • Do not lift the end of the SSD excessively.

    • Pull the drive straight out of its socket and remove it from the logic board.

    • When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.
    • Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    The following connector has an especially deep socket. Use care when disconnecting it.
    • The following connector has an especially deep socket. Use care when disconnecting it.

    • While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help "walk" it out of its socket.

    • Remove the I/O board cable.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.
    • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the following three screws securing the fan to the upper case:
    • Remove the following three screws securing the fan to the upper case:

    • Two 5.2 mm T5 Torx screws

    • One 3.6 mm T5 Torx screw

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.
    • Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the following five screws securing the battery to the upper case:
    • Remove the following five screws securing the battery to the upper case:

    • Two 5.2 mm T5 Torx screws

    • One 6 mm T5 Torx screw

    • Two 2.6 mm T5 Torx screws

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Do not touch or squeeze the six lithium polymer cells when handling the battery.
    • Do not touch or squeeze the six lithium polymer cells when handling the battery.

    • Lift the battery from its edge nearest the logic board and remove it from the upper case.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Disconnect the I/O board by pulling the power cable away from its socket on the logic board.
    • Disconnect the I/O board by pulling the power cable away from its socket on the logic board.

    • Pull the cable parallel to the face of the logic board toward the front edge of the Air.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the tip of a spudger to carefully flip up the retaining flap on the microphone cable ZIF socket. Be sure you are prying up on the retaining flap, not the socket itself.
    • Use the tip of a spudger to carefully flip up the retaining flap on the microphone cable ZIF socket.

    • Be sure you are prying up on the retaining flap, not the socket itself.

    • Pull the microphone ribbon cable straight out of its socket.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.
    • Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.

    • Pry up from beneath the wires.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Pull the camera cable parallel to the face of the I/O board toward the rear edge of the Air to disconnect it from its socket.
    • Pull the camera cable parallel to the face of the I/O board toward the rear edge of the Air to disconnect it from its socket.

    • Do not lift upward on this cable as you disconnect it, as its socket may break off the logic board.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the small rubber gasket from the corner of the upper case nearest the I/O board.
    • Remove the small rubber gasket from the corner of the upper case nearest the I/O board.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the single 3.6 mm T5 Torx screw securing the I/O board to the upper case.
    • Remove the single 3.6 mm T5 Torx screw securing the I/O board to the upper case.

  19. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Carefully lift the I/O board from its edge nearest the logic board and remove it from the upper case.
    • Carefully lift the I/O board from its edge nearest the logic board and remove it from the upper case.

Linea Traguardo

Altre 15 persone hanno completato questa guida.

Un commento

Question. Im looking a replacing the I/O board on my MacBook air and am wondering if it matters whether I get the board for the 13” or the 11”? Are the two boards different? It seems that the 11” I/O board is cheaper so I just trying to figure out if it matters which one I get?

Tristan cusi - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 9

Ultimi 30 Giorni: 31

Tutti i Tempi: 13,852