MacBook Air 11" Late 2010 Fan Replacement

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

Passo 1 Scocca inferiore

, Scocca inferiore: passo 1, immagine 1 di 1

Attrezzo utilizzato in questo passaggio:

P5 Pentalobe Screwdriver Retina MacBook Pro and Air

$5.99

Compra

Prima di cominciare, chiudi il tuo portatile e appoggialo a testa in giù su una superfice morbida.
Svita le seguenti dieci viti:
Due viti pentalobe da 8 mm
Otto viti pentalobe da 2,5 mm
Il cacciavite speciale richiesto per svitare le viti Pentalobe può essere trovato qui.

Traduci

I recommend that one of the tools you obtain is a jeweler's loupe that mounts on your glasses. It makes things easier.

blairweaver - 26 gen 2017 Replica

This is not correct. You need the pentalobe tool at this point.

Duane Hellums - 5 feb 2017 Replica

Passo 2

Infila le dita tra lo schermo e il case inferiore e tira verso l'alto per sganciare la cover dal MacBook Air.
Rimuovi la cover inferiore e mettila da parte.

Traduci

Passo 3

Questo passaggio è privo di traduzione. Aiuta a tradurlo

In this step you will disconnect the battery to help avoid shorting out any components during service.
Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
Bend the battery cable slightly away from the logic board so the connector will not accidentally contact its socket.

Traduci

Passo 4

Questo passaggio è privo di traduzione. Aiuta a tradurlo

Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

Traduci

What happens if the 2.9mm t5 screw got stripped?

Charles - 12 giu 2014 Replica

So when i change my ssd in mac do i have to reinstall Mac OS

sai prahalad Alluri - 26 apr 2015 Replica

Correct, the SSD does not come with OS preinstalled. To install the OS you can completely clone your existing hard drive or you will need to create a bootable flash drive and format your SSD and create a partition in order to be able to install the OS.

Ethan Lockwood - 28 apr 2015

So my wife spilled a Martini on her MacAir and it no longer works and is not repairable, all her music and pictures are stored on the drive, I would like to transfer these files to another drive. What is needed to read the drive once removed?

prastonis - 2 set 2015 Replica

Passo 5

Questo passaggio è privo di traduzione. Aiuta a tradurlo

Use a spudger to help lift the free end of the SSD just enough to grab it with your other hand.
Do not lift the end of the SSD excessively.
Pull the drive straight out of its socket and remove it from the logic board.
When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

Traduci

I performed all the steps above and fitted a Transcend JetDrive 500 which was very easy however when I re-assembled and turned on all I get is a question mark in the middle of the screen, can you explain if I did anything wrong?

Ian Ashton - 24 nov 2016 Replica

Passo 6

Questo passaggio è privo di traduzione. Aiuta a tradurlo

Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

Traduci

Passo 7

Questo passaggio è privo di traduzione. Aiuta a tradurlo

The following connector has an especially deep socket. Use care when disconnecting it.
While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help "walk" it out of its socket.
Remove the I/O board cable.

Traduci

Passo 8

Questo passaggio è privo di traduzione. Aiuta a tradurlo

Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, not the socket itself.