Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

MacBook Air 11" Early 2015 I/O Board Replacement

Cosa ti serve

  1. MacBook Air 11" Early 2015 I/O Board Replacement, Lower Case: passo 1, immagine 1 di 1
    Attrezzo utilizzato in questo passaggio:
    P5 Pentalobe Screwdriver Retina MacBook Pro and Air
    $5.99
    Compra
    • Shut down and close your computer. Lay it on a soft surface top-side down.

    • Remove the following ten screws:

    • Two 8 mm 5-point Pentalobe screws

    • Eight 2.5 mm 5-point Pentalobe screws

    • The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

  2. MacBook Air 11" Early 2015 I/O Board Replacement: passo 2, immagine 1 di 1
    • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

  3. MacBook Air 11" Early 2015 I/O Board Replacement, Battery Connector: passo 3, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement, Battery Connector: passo 3, immagine 2 di 2
    • In this step you will disconnect the battery to help avoid shorting out any components during service.

    • Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

    • Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.

  4. MacBook Air 11" Early 2015 I/O Board Replacement, I/O Board Cable: passo 4, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement, I/O Board Cable: passo 4, immagine 2 di 2
    • Use the flat end of a spudger to pry the left and right I/O board cable connectors up off their respective sockets on the I/O board.

  5. MacBook Air 11" Early 2015 I/O Board Replacement: passo 5, immagine 1 di 1
    • Lift and remove the I/O board cable.

  6. MacBook Air 11" Early 2015 I/O Board Replacement, Fan: passo 6, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement, Fan: passo 6, immagine 2 di 2
    • Use the tip of a spudger to carefully push on each side of the iSight camera cable connector to loosen it out of its socket on the logic board.

    • We recommend you gently "walk" the connector out of its socket.

  7. MacBook Air 11" Early 2015 I/O Board Replacement: passo 7, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement: passo 7, immagine 2 di 2
    • Peel the iSight camera cable up off the adhesive securing it to the fan.

  8. MacBook Air 11" Early 2015 I/O Board Replacement: passo 8, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement: passo 8, immagine 2 di 2
    • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

  9. MacBook Air 11" Early 2015 I/O Board Replacement: passo 9, immagine 1 di 1
    • Remove the following three screws securing the fan to the upper case:

    • Two 5.5 mm T5 Torx screws

    • One 4.6 mm T5 Torx screw

    • In some models this is a 3.6 mm T5 Torx screw.

  10. MacBook Air 11" Early 2015 I/O Board Replacement: passo 10, immagine 1 di 3 MacBook Air 11" Early 2015 I/O Board Replacement: passo 10, immagine 2 di 3 MacBook Air 11" Early 2015 I/O Board Replacement: passo 10, immagine 3 di 3
    • Lift, but do not remove the fan out of its recess in the upper case.

    • Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air.

  11. MacBook Air 11" Early 2015 I/O Board Replacement, Battery: passo 11, immagine 1 di 1
    • Remove the following five screws securing the battery to the upper case:

    • Two 5.2 mm T5 Torx screws

    • One 6 mm T5 Torx screw

    • Two 2.6 mm T5 Torx screws

  12. MacBook Air 11" Early 2015 I/O Board Replacement: passo 12, immagine 1 di 1
    • When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.

    • Lift the battery from its edge nearest the logic board and remove it from the upper case.

  13. MacBook Air 11" Early 2015 I/O Board Replacement, I/O Board: passo 13, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement, I/O Board: passo 13, immagine 2 di 2
    • Disconnect the I/O board power cable from the logic board by pulling the cable out of its socket on the logic board.

    • Pull the cable parallel to the face of the logic board toward the front edge of the Air.

  14. MacBook Air 11" Early 2015 I/O Board Replacement: passo 14, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement: passo 14, immagine 2 di 2
    • If necessary, use tweezers to remove any tape covering the microphone cable ZIF connector.

  15. MacBook Air 11" Early 2015 I/O Board Replacement: passo 15, immagine 1 di 3 MacBook Air 11" Early 2015 I/O Board Replacement: passo 15, immagine 2 di 3 MacBook Air 11" Early 2015 I/O Board Replacement: passo 15, immagine 3 di 3
    • Use the tip of a spudger to carefully flip up the retaining flap on the microphone cable ZIF socket.

    • Be sure you are prying up on the retaining flap, not the socket itself.

    • Pull the microphone ribbon cable straight out of its socket.

  16. MacBook Air 11" Early 2015 I/O Board Replacement: passo 16, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement: passo 16, immagine 2 di 2
    • Use the tip of a spudger to pry under the speaker cable near the connector to lift the connector straight up out of its socket.

  17. MacBook Air 11" Early 2015 I/O Board Replacement: passo 17, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement: passo 17, immagine 2 di 2
    • De-route the cable from its notch in the I/O board.

  18. MacBook Air 11" Early 2015 I/O Board Replacement: passo 18, immagine 1 di 2 MacBook Air 11" Early 2015 I/O Board Replacement: passo 18, immagine 2 di 2
    • Remove the small rubber gasket from the corner of the upper case nearest the I/O board.

  19. MacBook Air 11" Early 2015 I/O Board Replacement: passo 19, immagine 1 di 1
    • Remove the single 3.6 mm T5 Torx screw securing the I/O board to the upper case.

    • In some models this is a 3.1 mm T5 Torx screw.

  20. MacBook Air 11" Early 2015 I/O Board Replacement: passo 20, immagine 1 di 3 MacBook Air 11" Early 2015 I/O Board Replacement: passo 20, immagine 2 di 3 MacBook Air 11" Early 2015 I/O Board Replacement: passo 20, immagine 3 di 3
    • Carefully lift the I/O board by its power cable and pull it away from the edge of the case.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 9 persone hanno completato questa guida.

Sam Goldheart

Membro da: 10/18/12

465.243 Reputazione

538 Guide realizzate

Team

iFixit Membro di iFixit

Staff

136 Membri

16.562 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 4

Ultimi 7 Giorni: 13

Ultimi 30 Giorni: 47

Tutti i Tempi: 6,450