Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Power down your Mac mini, disconnect all of the cables, and flip it over.
-
Insert the Jimmy into the crack between the aluminum top housing and the plastic lower housing.
-
The Jimmy should reach a stop about 3/8" down.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently bend the Jimmy outwards to pry the crack open a little larger and lift the lower housing up a small amount.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Once you have the first side free, rotate the Mac mini and start prying up on the front edge.
-
Use the same prying motion to both bend the clips inward and lift the lower housing up out of the top housing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Keep working around the perimeter, freeing the clips along the final edge.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip the Mac mini back over and lift the top housing off of the lower housing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
We will first remove the AirPort antenna, located in the lower left corner of this picture.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slightly squeeze the two retaining arms toward each other and lift the AirPort antenna off its post.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grab the Bluetooth antenna nearest the port side of the computer by the edges of the board and pull it straight up off the internal frame.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the antenna board near the front of the mini by pulling it straight up off the internal frame.
-
If necessary, remove the piece of tape securing the antenna leads to the internal frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry the audio ribbon cable connector up off the audio board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the following four screws securing the internal frame to the bottom housing:
-
Three 6.7 mm Phillips #00 screws
-
One 9.5 mm Phillips #00 screw
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the internal frame off the bottom housing, starting at the rear edge, until you feel the concealed edge connector on the motherboard disconnect. Then lift straight off, minding the bluetooth and 802.11 antenna cables.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the tip of a spudger to remove the black electrical tape spanning the interconnect board and optical drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to disconnect the audio ribbon cable from the interconnect board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
If necessary, remove the yellow kapton tape covering the internal frame and the optical drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips screws securing the optical drive to the internal frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the mini 180 degrees and remove the two Phillips screws securing the optical drive to the internal frame on the other side.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two Phillips screws securing the interconnect board to the optical drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert the flat end of a spudger into the crevice between the optical drive and the interconnect board.
-
Carefully increase the crevice to disconnect the optical drive from the interconnect board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently lift the optical drive out of the internal frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single Phillips screw securing the IR board to the internal frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
De-route the IR board and cable through the opening in the internal frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
De-route the IR board cable from the channel along the internal frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to pry the IR board connector up off the interconnect board and remove the IR board from your mini.
-
Annulla: non ho completato questa guida.
Altre 2 persone hanno completato questa guida.