Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the spudger to separate the back plate from the rest of the computer with the screen up like in the picture.
-
Once the back plate is loose, close the screen for an easier time properly removing it.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using a Phillips Head #1 screwdriver, unscrew the 15 screws on the bottom of the device
-
After all the screws are unscrewed, remove the bottom plate. If this is the first time that you are removing this back cover, the last screw is hidden under the "factory seal" label. You will need to break that label to reach that screw.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Locate the battery.
-
Wedge the spudger underneath the battery, and apply pressure to lift it away from the rest of the device.
-
Gently pull and wiggle the multiple colored wired connector out from the socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Locate the hard drive.
-
Using a spudger lift the ribbon cable connector.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the tweezers to lift the back tab and pull it back until the ribbon cable disconnects.
-
Wedge the spudger between the hard drive and the device and apply pressure to pry the two apart, and then remove the hard drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
First locate the speaker(s).
-
Use the tweezers to lift the speaker from its position.
-
Grab the multi-colored wire with the tweezers and gently pull back until the speakers releases from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
First, locate all the ribbon cables that are connected to the motherboard.
-
Lift the ribbon cable connector tabs with the spudger gently.
-
Using the tweezers, gently pull back on the ribbon cable until it is completely out of the socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
First, locate all the screws holding down the Motherboard.
-
Remove all the screws using the #1 Phillips head screw driver.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Next, locate the Wi-Fi chip.
-
Use the #1 Phillips head screwdriver to remove the screw attaching the Wi-fi chip to the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the spudger to lift the motherboard up and remove it from the laptop, then flip the now separated motherboard over.
-
Using tweezers, disconnect the red wire circled in the picture; where the hard drive would be.
-
Locate the SSD and the screw holding it in.
-
Unscrew the one Screw using a #1 Phillips Head screwdriver.
-
The SSD will want to lift with that screw being removed, from here grab it and pull it out gently.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Locate the RAM.
-
Pull back the two tabs holding it into place, it will pop out.
-
Pull it out.
-
Annulla: non ho completato questa guida.
Altre 13 persone hanno completato questa guida.
4 Commenti
Super helpful. Thanks.
Thanks, it works on my gs63 8re with minor adjustments (no need to move the speakers)
Great guide! I used this guide to replace the GPU and CPU fans since one has to remove the mobo in order to do so.
Which screws go where?